Advice on coal stove setup

Post Reply
User avatar
Lightning
Site Moderator
Posts: 14677
Joined: Wed. Nov. 16, 2011 9:51 am
Stoker Coal Boiler: Modified AA 130
Coal Size/Type: Pea Size - Anthracite
  • Quote

Post by Lightning »

Hi Jeff, welcome to the coal board. Getting around the fireplace damper is challenging, I ended up cutting some of it out of the way. Other than that, once you get the pipe up into the chimney (a few feet is plenty) it needs to be sealed against the chimney walls. Simply stuff fiberglass insulation or rock wool between the pipe and the chimney wall to make the seal.


Old Jeff
New Member
Posts: 11
Joined: Sat. Sep. 02, 2023 11:27 am
Hand Fed Coal Stove: Hitzer 50-93
Coal Size/Type: blaschak nut
Other Heating: Oil forced hot air
  • Quote

Post by Old Jeff »

thanks for all the help....located some flex liner on marketplace, guy had some leftover from his job. still checking out stoves, the guy that has the 50-93 is out of town this week,so i will check on that asap. ive got my eyes open for other deals in the mean time. ill keep you posted on progress. id like to have a setup in place by beginning of october!

Hoytman
Missed and Always Remembered
Posts: 6110
Joined: Wed. Jan. 18, 2017 11:30 pm
Hand Fed Coal Stove: Hitzer 354
Coal Size/Type: nut coal
Other Heating: electric, wood, oil
  • Quote

Post by Hoytman »

For that price $1500 that stove should be clean inside and out like a new one…even with the rise in prices, or else be patient and wait. There will be more. If looks good inside, glass is clean, grates good, paint like new…might want to grab it.

I’m seeing some that are newer and not maintained well, paint is all rust and asking >$1500+. I wish them good luck with that. I’m not paying that much for a newer abused Hitzer. Often times it’s those $700-$800 stoves that look better than some higher priced that people didn’t take care of.

Yes….with inflation things will be higher, but be picky and patient. Deals still out there. Asking and getting are two different things for abused stoves.

User avatar
Sunny Boy
Member
Posts: 26445
Joined: Mon. Nov. 11, 2013 1:40 pm
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace
  • Quote

Post by Sunny Boy »

The high price of coal may have an impact on used coal stove prices. As a result, quite a few members on here have mentioned switching away from coal.

I know I'd hate to be trying to sell a coal stove now.

Paul

Old Jeff
New Member
Posts: 11
Joined: Sat. Sep. 02, 2023 11:27 am
Hand Fed Coal Stove: Hitzer 50-93
Coal Size/Type: blaschak nut
Other Heating: Oil forced hot air
  • Quote

Post by Old Jeff »

All good points, and i will continue to look....but i just had oil delivered this morning here in nj. i have a small cottage on my property that i rent out. $ 4.07 per gallon. i weighed my options about alternative heat, i still felt coal was best way to go even at $430 per ton bagged. wood pellets are around 350 per ton? aint nothing cheap in this country anymore. we have a govt that hates fossil fuels and i dont see that policy changing anytime soon. And even if we get a change in president, that wont be until Next january! IM really hoping that my coal setup can heat my whole house, even if i have to run my furnace first thing in the morning for an hour or so on the coldest days of winter...time will tell.

waytomany?s
Member
Posts: 4992
Joined: Fri. Aug. 16, 2019 3:02 pm
Hand Fed Coal Stove: Harmon Mark II
Hand Fed Coal Furnace: Looking
Baseburners & Antiques: Looking
Coal Size/Type: Nut
Other Heating: newmac wood/coal combo furnace
  • Quote

Post by waytomany?s »

You're going to burn a lot of coal to heat that great room. I'd be surprised if the heat migration is much if at all. It may help you lessen the heat load on the furnace though. Cost savings may be negligible, however you won't know until you try. Try and keep track of the numbers. It will be interesting to see.

Old Jeff
New Member
Posts: 11
Joined: Sat. Sep. 02, 2023 11:27 am
Hand Fed Coal Stove: Hitzer 50-93
Coal Size/Type: blaschak nut
Other Heating: Oil forced hot air
  • Quote

Post by Old Jeff »

Well i guess i will find out about heat migration, would a box fan at the kitchen door move warm air into the other side of the home?


waytomany?s
Member
Posts: 4992
Joined: Fri. Aug. 16, 2019 3:02 pm
Hand Fed Coal Stove: Harmon Mark II
Hand Fed Coal Furnace: Looking
Baseburners & Antiques: Looking
Coal Size/Type: Nut
Other Heating: newmac wood/coal combo furnace
  • Quote

Post by waytomany?s »

Cold air is heavier, aim fan to push/pull it towards the stove.

User avatar
warminmn
Member
Posts: 8712
Joined: Tue. Feb. 08, 2011 5:59 pm
Hand Fed Coal Stove: Chubby Junior, Riteway 37
Coal Size/Type: nut ant, lignite
Other Heating: Wood and wear a wool shirt
  • Quote

Post by warminmn »

Way is spot on. Took me years to learn it but push the cold air towards the heat with a fan on the floor. Then stand in doorway and feel the heat coming back at you. Then you'll be convinced.

You'll have to try it a few different ways to find what works best.

Old Jeff
New Member
Posts: 11
Joined: Sat. Sep. 02, 2023 11:27 am
Hand Fed Coal Stove: Hitzer 50-93
Coal Size/Type: blaschak nut
Other Heating: Oil forced hot air
  • Quote

Post by Old Jeff »

Very interesting stuff, I’m sure there’s a learning curve to be had here.

User avatar
warminmn
Member
Posts: 8712
Joined: Tue. Feb. 08, 2011 5:59 pm
Hand Fed Coal Stove: Chubby Junior, Riteway 37
Coal Size/Type: nut ant, lignite
Other Heating: Wood and wear a wool shirt
  • Quote

Post by warminmn »

Ha ha, yes there is a learning curve! After heating with wood for years here with a fan sitting by the stove blowing the heat towards the room I sleep in (or trying too), I started burning coal, found this forum, and read the posts on this forum religiously and didnt really believe it until I tried it.

I have a roughly 2 foot drop between my living room and the other 2 downstairs rooms. Whichever section I am burning in I put a fan on the floor blowing into the room with a stove running and my house is a much more consistent temp. I also have ceiling fans in each room but the floor fan brings the heat to the other section, not the ceiling fan.

If a house was a leaky mess it might not matter. Otherwise it works. Just try it when the stove is putting out serious heat and stand in the doorway where the fan is and you'll feel the heat coming back. Then try turning the fan around and you'll need a sweater...

Hoytman
Missed and Always Remembered
Posts: 6110
Joined: Wed. Jan. 18, 2017 11:30 pm
Hand Fed Coal Stove: Hitzer 354
Coal Size/Type: nut coal
Other Heating: electric, wood, oil
  • Quote

Post by Hoytman »

Yup! Good post warm.

Den034071
Member
Posts: 911
Joined: Sat. Jun. 25, 2011 4:30 pm
Hand Fed Coal Stove: Hitzer, 3095
  • Quote

Post by Den034071 »

Jeff i sent you a private message on a Gibraltar very large stove .Check top right corner of page jack in Penna .

Old Jeff
New Member
Posts: 11
Joined: Sat. Sep. 02, 2023 11:27 am
Hand Fed Coal Stove: Hitzer 50-93
Coal Size/Type: blaschak nut
Other Heating: Oil forced hot air
  • Quote

Post by Old Jeff »

Appreciate all of the help with suggestions for my Coal Stove set up. I picked up a used hitzer 50-93 about one month ago. Stove appeared to be in excellent shape and the price was right, so I made the deal. Lots of family stuff going on in the past month, so just getting around to finishing the set up now. Took the advice of most on here, found a piece of stainless steel liner 10 feet long, removed damper, put it up above the smoke shelf stuffed with Rockwool. I’m trying to figure out the best way to run the pipe. The stove is sitting on the hearth, so I’m inside the firebox of the old fireplace. There is not a lot of room to work, and I’m wondering what kind of set up I should use. Should I come straight out of the stove outlet horizontal, into a T and then up to the liner? I want to keep the liner above the arch of the fireplace so it cannot be seen. I’m wondering if the horizontal coming out of the outlet needs some angle on it, or is it going to draft right from the tee? I want to put a damper in just before the hook up to the stainless liner. There’s not a lot of pipe to be run, but it’s a cramped space and really not an easy spot to work in. Advice would be appreciated. I’ll send some pictures.

Jeff

Attachments

Legend:
Download File
File Information
File Comment
Copy [BBcode] to Clipboard
IMG_7028.jpeg

IMG_7028.jpeg

IMG_7029.jpeg

IMG_7029.jpeg

IMG_7026.jpeg

IMG_7026.jpeg


User avatar
ShawnLiNy
Member
Posts: 633
Joined: Fri. Nov. 30, 2018 12:28 am
Hand Fed Coal Stove: Waterford
Coal Size/Type: Nut
  • Quote

Post by ShawnLiNy »

Sheet metal shroud width of stove spray with high heat black and hang on 2 pegs /drilled or epoxied above so it’s easily removable


Post Reply

Return to “Hand Fired Coal Stoves & Furnaces Using Anthracite”