Sluggish Water Temps

Post Reply
 
Matt328
Member
Posts: 29
Joined: Sun. Feb. 24, 2013 1:28 pm
Location: Tyrone, PA
Hand Fed Coal Boiler: Van Wert Simplex Multitherm
Coal Size/Type: Chestnut Anthracite
Other Heating: Mendota Propane Stove

Post by Matt328 » Wed. Dec. 30, 2020 11:25 am

This year I've notice my system has been really slow to respond when there is a lot of demand for heat, when 2 or more zones call for heat at the same time, as they do first thing in the morning when the thermostats automatically jump up 2 degrees. This morning in particular it was very slow to respond, the house was pretty chilly, and my water temp dipped down to 110 degrees. I've never seen it that low unless the fire was completely out. Surprisingly, I had plenty of fire in the firebox, it looked really healthy and was putting off a decent amount of heat, it just seemed like it wasn't being transferred to the water very efficiently. The basement zone has 2 large cast iron radiators, and that zone was calling for heat at the same time as the other two, so possibly it's as simple as staggering the thermostats so its not trying to bring up the entire house at the same time.

I haven't had this issue in previous years, on the contrary, my basement is my dump zone, and would pretty much always keep the radiators warm just dumping alone. This year though, I tried to address that by making some adjustments to the barometric damper. After taking it off and cleaning and adjusting it, I discovered it was set up completely backwards, set for a vertical installation, while I have it installed horizontally. I'm thinking that worked a little too well and I might just have to experiment and get it dialed in better.

I had some ash built up in the heat exchanger which I cleaned out this morning, but I know I've definitely seen it worse.

My question is, are there any other things to check if I have plenty of fire, but the water just isn't heating up as quickly as it usually is?

 
User avatar
coaledsweat
Site Moderator
Posts: 13763
Joined: Fri. Oct. 27, 2006 2:05 pm
Location: Guilford, Connecticut
Stoker Coal Boiler: Axeman Anderson 260M
Coal Size/Type: Pea

Post by coaledsweat » Wed. Dec. 30, 2020 11:34 am

You don't mention your device's brand name so I'll take a shot it has a squirrel cage combustion draft blower. If so, clean the blower blades with a tooth brush. They tend to pick up hair and dust which can reduce its ability to move air by a massive amount. If not, check the stovepipe for ash accumulation. That's all I've got until there's more info.

 
User avatar
Lightning
Site Moderator
Posts: 14658
Joined: Wed. Nov. 16, 2011 9:51 am
Location: Olean, NY
Stoker Coal Boiler: Modified AA 130
Coal Size/Type: Pea Size - Anthracite

Post by Lightning » Wed. Dec. 30, 2020 11:49 am

Van Wert Simplex Multitherm

In his profile.

 
User avatar
freetown fred
Member
Posts: 30293
Joined: Thu. Dec. 31, 2009 12:33 pm
Location: Freetown,NY 13803
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut

Post by freetown fred » Wed. Dec. 30, 2020 12:35 pm

Well, that proves it Lee----when your not drinkin---you're thinkin!!!!!!!!!!!!!!!!!!!!!!!!!! LOL


 
Jlinde37
Member
Posts: 89
Joined: Sat. Jan. 06, 2018 9:40 am
Location: Ellicottville, Ny
Hand Fed Coal Boiler: DS Aquagem 3200
Coal Size/Type: Nut/Pea

Post by Jlinde37 » Wed. Dec. 30, 2020 1:49 pm

Same thing happens when my radiant slab hasn't run all on a sunny day and the concrete gets cold. Then in the evening the first time that 1020sqft slab calls for heat its such a surge of cold water the boiler drops down to like 140 and takes a little while to recover. I feel its normal as everything coal is slow. Slow to ramp up the bed and slow heating 40gallons of water 40 degrees.
I now have a tekmar thermostat with sensor that keeps slab at 65.

 
User avatar
Rob R.
Site Moderator
Posts: 17979
Joined: Fri. Dec. 28, 2007 4:26 pm
Location: Chazy, NY
Stoker Coal Boiler: EFM 520
Hand Fed Coal Stove: Chubby Jr

Post by Rob R. » Wed. Dec. 30, 2020 2:01 pm

Staggering those thermostats would help, and so would throttling the flow of water to those zones.

It is also possible your coal is different and not as responsive.

 
User avatar
McGiever
Member
Posts: 10130
Joined: Sun. May. 02, 2010 11:26 pm
Location: Junction of PA-OH-WV
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hand Fed Coal Boiler: BUCKET A DAY water heater
Hand Fed Coal Stove: Warm Morning 414A
Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
Other Heating: Ground Source Heat Pump and some Solar

Post by McGiever » Sat. Jan. 02, 2021 1:53 pm

So, circ. pump are working 100%???

Another thought is, maybe air pocket blocking...or air pocket in pump...do some air bleeding.

 
User avatar
freetown fred
Member
Posts: 30293
Joined: Thu. Dec. 31, 2009 12:33 pm
Location: Freetown,NY 13803
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut

Post by freetown fred » Sat. Jan. 02, 2021 3:01 pm

A BIG plus 1---sometimes the obvious escapes us???


 
07roadstar
Member
Posts: 75
Joined: Wed. Jan. 25, 2012 8:40 pm
Location: Keeseville, Ny
Hand Fed Coal Furnace: Had DS basement stove
Coal Size/Type: Nut
Other Heating: Burnham oil burner boiler

Post by 07roadstar » Fri. Jan. 08, 2021 11:26 am

If you have the automatic vent valves to purge air , you might want to check them. Check your feeder valve along with the backflow preventer. Check your expansion valve and check valve. Check these after you purge your system. Good luck.

 
lzaharis
Member
Posts: 2365
Joined: Sun. Mar. 25, 2007 8:41 pm
Location: Ithaca, New York
Stoker Coal Boiler: Keystoker KAA-4-1 dual fuel boiler
Hand Fed Coal Boiler: former switzer CWW100-sold
Coal Size/Type: rice
Other Heating: kerosene for dual fuel Keystoker/unused

Post by lzaharis » Sat. Jan. 09, 2021 10:31 am

When you say you adjusted your barometric damper;
are you telling us that the damper door weight is not
pushed all the way to the right and locked in place
which is what the folks at Field Controls want to see
on a coal boiler?

 
User avatar
coaledsweat
Site Moderator
Posts: 13763
Joined: Fri. Oct. 27, 2006 2:05 pm
Location: Guilford, Connecticut
Stoker Coal Boiler: Axeman Anderson 260M
Coal Size/Type: Pea

Post by coaledsweat » Sat. Jan. 09, 2021 11:34 am

Couldn't have been too serious, he hasn't been back since he made the OP.

 
Matt328
Member
Posts: 29
Joined: Sun. Feb. 24, 2013 1:28 pm
Location: Tyrone, PA
Hand Fed Coal Boiler: Van Wert Simplex Multitherm
Coal Size/Type: Chestnut Anthracite
Other Heating: Mendota Propane Stove

Post by Matt328 » Thu. Dec. 08, 2022 9:27 am

I realize this was 2 years ago, but for posterity, I cleaned out my heat exchanger area and set up the baro damper for a coal boiler, and things have been working ok. I think that one morning was just a perfect storm where the outdoor temps dropped quickly and my 2 basement radiators were ice cold when the thermostats started calling for heat.

Post Reply

Return to “Hand Fired Coal Boilers Using Anthracite”