Page 3 of 3

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 2:07 pm
by dilly358
So strange named after planets

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 3:27 pm
by ShawnLiNy
dilly358 wrote:
Wed. Nov. 08, 2023 2:07 pm
So strange named after planets
looks like no parts are listed for this model , but look at the the parts lists from other models they likely used the same plates for whatever purpose

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 3:46 pm
by dilly358
Thanks since brand new never used is good should last years before need to find parts

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 3:46 pm
by dilly358
Coal is getting phased out soon too so I love heating with coal

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 4:51 pm
by dilly358
Also my dial on side goes up to 8 what is best setting

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 4:53 pm
by dilly358
Here's my dial

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 4:54 pm
by franco b
dilly358 wrote:
Wed. Nov. 08, 2023 4:51 pm
Also my dial on side goes up to 8 what is best setting
The best setting is when the air flap is closed or almost closed when the stove is at the temperature you want. Use a flashlight.

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 4:57 pm
by dilly358
Thanks the disc in where Ashland is on right side doesn't open much there's two holes on the round thing it only moves left to right a bit

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 4:58 pm
by dilly358
Doesn't open or move much with dial

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 5:00 pm
by dilly358
Here it is just moves a little left or right maybe opens a hair

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 5:04 pm
by franco b
It should be moving away from stove surface to open. With a cold stove it should be wide open.

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 5:08 pm
by dilly358
Yea only opens a hair or closes no matter how high or low on dial

Re: HAAS+SOHN???

Posted: Wed. Nov. 08, 2023 5:24 pm
by franco b
dilly358 wrote:
Wed. Nov. 08, 2023 5:08 pm
Yea only opens a hair or closes no matter how high or low on dial
I don't think it is working right. I would pull the dial and remove the plate to get at and observe the operation and adjust as needed.

Re: HAAS+SOHN???

Posted: Fri. Nov. 10, 2023 9:47 am
by dilly358
Thanks so much for in put I spun the disk to the right a few spins from the bottom where Ashbin is now it opens and closes 8 is wide open and lower u go it closes

Re: HAAS+SOHN???

Posted: Sat. Feb. 17, 2024 11:27 am
by mwzad
dilly358 wrote:
Fri. Nov. 10, 2023 9:47 am
Thanks so much for in put I spun the disk to the right a few spins from the bottom where Ashbin is now it opens and closes 8 is wide open and lower u go it closes
I sent you a pm on your haas sohn stove. Always good to talk to someone who is running the same unit!