HAAS+SOHN???

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 2:07 pm

So strange named after planets


 
User avatar
ShawnLiNy
Member
Posts: 627
Joined: Fri. Nov. 30, 2018 12:28 am
Hand Fed Coal Stove: Waterford
Coal Size/Type: Nut

Post by ShawnLiNy » Wed. Nov. 08, 2023 3:27 pm

dilly358 wrote:
Wed. Nov. 08, 2023 2:07 pm
So strange named after planets
looks like no parts are listed for this model , but look at the the parts lists from other models they likely used the same plates for whatever purpose

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 3:46 pm

Thanks since brand new never used is good should last years before need to find parts

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 3:46 pm

Coal is getting phased out soon too so I love heating with coal

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 4:51 pm

Also my dial on side goes up to 8 what is best setting

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 4:53 pm

Here's my dial

Attachments

20231108_165224.jpg
.JPG | 413.6KB | 20231108_165224.jpg

 
franco b
Site Moderator
Posts: 11417
Joined: Wed. Nov. 05, 2008 5:11 pm
Location: Kent CT
Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
Baseburners & Antiques: Glenwood Modern Oak 114
Coal Size/Type: nut and pea

Post by franco b » Wed. Nov. 08, 2023 4:54 pm

dilly358 wrote:
Wed. Nov. 08, 2023 4:51 pm
Also my dial on side goes up to 8 what is best setting
The best setting is when the air flap is closed or almost closed when the stove is at the temperature you want. Use a flashlight.


 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 4:57 pm

Thanks the disc in where Ashland is on right side doesn't open much there's two holes on the round thing it only moves left to right a bit

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 4:58 pm

Doesn't open or move much with dial

Attachments

20231108_165749.jpg
.JPG | 307.7KB | 20231108_165749.jpg

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 5:00 pm

Here it is just moves a little left or right maybe opens a hair

Attachments

20231108_165749.jpg
.JPG | 307.7KB | 20231108_165749.jpg

 
franco b
Site Moderator
Posts: 11417
Joined: Wed. Nov. 05, 2008 5:11 pm
Location: Kent CT
Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
Baseburners & Antiques: Glenwood Modern Oak 114
Coal Size/Type: nut and pea

Post by franco b » Wed. Nov. 08, 2023 5:04 pm

It should be moving away from stove surface to open. With a cold stove it should be wide open.

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Wed. Nov. 08, 2023 5:08 pm

Yea only opens a hair or closes no matter how high or low on dial

 
franco b
Site Moderator
Posts: 11417
Joined: Wed. Nov. 05, 2008 5:11 pm
Location: Kent CT
Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
Baseburners & Antiques: Glenwood Modern Oak 114
Coal Size/Type: nut and pea

Post by franco b » Wed. Nov. 08, 2023 5:24 pm

dilly358 wrote:
Wed. Nov. 08, 2023 5:08 pm
Yea only opens a hair or closes no matter how high or low on dial
I don't think it is working right. I would pull the dial and remove the plate to get at and observe the operation and adjust as needed.

 
dilly358
New Member
Posts: 15
Joined: Tue. Nov. 07, 2023 10:36 am

Post by dilly358 » Fri. Nov. 10, 2023 9:47 am

Thanks so much for in put I spun the disk to the right a few spins from the bottom where Ashbin is now it opens and closes 8 is wide open and lower u go it closes

 
mwzad
New Member
Posts: 11
Joined: Sat. Oct. 07, 2017 11:44 am

Post by mwzad » Sat. Feb. 17, 2024 11:27 am

dilly358 wrote:
Fri. Nov. 10, 2023 9:47 am
Thanks so much for in put I spun the disk to the right a few spins from the bottom where Ashbin is now it opens and closes 8 is wide open and lower u go it closes
I sent you a pm on your haas sohn stove. Always good to talk to someone who is running the same unit!


Post Reply

Return to “Imported Hand Fired Coal Stoves Using Anthracite”