EFEL Stove Parts/Tools

Post Reply
birdsfan
New Member
Posts: 4
Joined: Mon. Feb. 26, 2018 2:49 pm
Hand Fed Coal Stove: Efel Arden
Coal Size/Type: Pea/Nut mix Anthracite from the Mammoth Vein
Stove/Furnace Make: EFEL
Stove/Furnace Model: ARDEN 084.65
Location: NEPA

Post By: birdsfan » Mon. Feb. 26, 2018 9:24 pm

Hello Everyone,

In my opinion I purchased the best hand fired coal stove made back in 1986, and it is still performing flawlessly to this day! Its an EFEL ARDEN (084.65). This stove has gotten us through many power failures and extreme temperatures without a hitch. I am having a hard time finding replacement tools for this stove. The USA Dealer site seems to not be online anymore. I need to replace the shaker tool. It slides over the shaker arm on the back upper part of the stove. Its not your regular run of the mill hook tool, it almost looks like a curtain rod. Anyone have contacts for parts and tool for this stove?

User avatar
McGiever
Member
Posts: 6933
Joined: Sun. May. 02, 2010 11:26 pm
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hand Fed Coal Boiler: BUCKET A DAY water heater
Hot Air Coal Stoker Furnace: Converted Riteway into a Stoker Fed
Hot Air Coal Stoker Stove: Harman Magnum
Hand Fed Coal Stove: Warm Morning 414A
Baseburners & Antiques: Our Glenwood 111 ; Art Garland 130 ; Favorite 513
Coal Size/Type: RICE,PEA,NUT,STOVE /ANTHRACITE and EGG / BIT
Other Heating: Ground Source Heat Pump and some Solar
Location: Junction of PA-OH-WV

Post By: McGiever » Mon. Feb. 26, 2018 9:48 pm

There is a member new to this forum that owns and runs a metal fabrication shop.

If you can sketch it with good dimensions he could certainly be able to reproduce it.

Post by cdindustries - Coal tools and parts

User avatar
warminmn
Member
Posts: 3167
Joined: Tue. Feb. 08, 2011 5:59 pm
Hand Fed Coal Stove: Chubby Junior, Efel Nestor Martin, Frankenstove
Coal Size/Type: nut and stove anthracite
Other Heating: wood and a little LP
Location: Land of 11,842 lakes

Post By: warminmn » Mon. Feb. 26, 2018 10:25 pm

I could probably provide measurements if I can find my tool, if its the same. Mine was an Efel Bayard, same as Harmony 3. I never used that end of the tool. I just sliced.

User avatar
freetown fred
Member
Posts: 23436
Joined: Thu. Dec. 31, 2009 12:33 pm
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut
Location: Freetown,NY 13803

Post By: freetown fred » Tue. Feb. 27, 2018 7:23 am

What the hell W--ya lost your TOOL???????????????? OUCH!!! LOL


User avatar
warminmn
Member
Posts: 3167
Joined: Tue. Feb. 08, 2011 5:59 pm
Hand Fed Coal Stove: Chubby Junior, Efel Nestor Martin, Frankenstove
Coal Size/Type: nut and stove anthracite
Other Heating: wood and a little LP
Location: Land of 11,842 lakes

Post By: warminmn » Tue. Feb. 27, 2018 8:11 am

freetown fred wrote:
Tue. Feb. 27, 2018 7:23 am
What the hell W--ya lost your TOOL???????????????? OUCH!!! LOL
Its been a while but I think I remember the last place I put it :lol:

User avatar
warminmn
Member
Posts: 3167
Joined: Tue. Feb. 08, 2011 5:59 pm
Hand Fed Coal Stove: Chubby Junior, Efel Nestor Martin, Frankenstove
Coal Size/Type: nut and stove anthracite
Other Heating: wood and a little LP
Location: Land of 11,842 lakes

Post By: warminmn » Tue. Feb. 27, 2018 8:15 am

found it, surprisingly. These are the 2 tools I have. If you dont have 1 for a pattern I can take better measurements to have 1 made.
Attachments
IMG_1599.JPG
IMG_1600.JPG
IMG_1601.JPG
IMG_1602.JPG

Den034071
Member
Posts: 581
Joined: Sat. Jun. 25, 2011 4:30 pm
Hand Fed Coal Stove: Hitzer, 3095

Post By: Den034071 » Wed. Feb. 28, 2018 9:02 am

The hook tool do the following .Buy a hickory replacement hammer handle .Drill a hole in end of handle .Buy a J yes a Jay hook an screw into handle .Walla I used this to shake my Franco Belge stove .It lasts for years .Jack

birdsfan
New Member
Posts: 4
Joined: Mon. Feb. 26, 2018 2:49 pm
Hand Fed Coal Stove: Efel Arden
Coal Size/Type: Pea/Nut mix Anthracite from the Mammoth Vein
Stove/Furnace Make: EFEL
Stove/Furnace Model: ARDEN 084.65
Location: NEPA

Post By: birdsfan » Wed. Feb. 28, 2018 6:47 pm

ImageHello All,
I hear ya about just getting a hook tool but the U-channel tool works much smoother. It is exactly the 2nd picture from warminmn. I attached a pic of my stove and worn out tool.
20180227_212224.jpg
Efel Arden
20180227_212402.jpg
Ahaker tool


User avatar
warminmn
Member
Posts: 3167
Joined: Tue. Feb. 08, 2011 5:59 pm
Hand Fed Coal Stove: Chubby Junior, Efel Nestor Martin, Frankenstove
Coal Size/Type: nut and stove anthracite
Other Heating: wood and a little LP
Location: Land of 11,842 lakes

Post By: warminmn » Wed. Feb. 28, 2018 9:17 pm

You might be able to have someone braze that to get it strong and the right size again, if its as thick of steel as mine. I'll dig online, probably tomorrow, as i used to have some websites saved for parts for mine. They likely used the same tool for many models.

birdsfan
New Member
Posts: 4
Joined: Mon. Feb. 26, 2018 2:49 pm
Hand Fed Coal Stove: Efel Arden
Coal Size/Type: Pea/Nut mix Anthracite from the Mammoth Vein
Stove/Furnace Make: EFEL
Stove/Furnace Model: ARDEN 084.65
Location: NEPA

Post By: birdsfan » Tue. Mar. 13, 2018 1:27 pm

Warminmn, were you able to find any of those parts websites that might list this shaker tool? Thanks!

User avatar
freetown fred
Member
Posts: 23436
Joined: Thu. Dec. 31, 2009 12:33 pm
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut
Location: Freetown,NY 13803

Post By: freetown fred » Tue. Mar. 13, 2018 1:29 pm

Did ya contact CD Industries?

User avatar
warminmn
Member
Posts: 3167
Joined: Tue. Feb. 08, 2011 5:59 pm
Hand Fed Coal Stove: Chubby Junior, Efel Nestor Martin, Frankenstove
Coal Size/Type: nut and stove anthracite
Other Heating: wood and a little LP
Location: Land of 11,842 lakes

Post By: warminmn » Tue. Mar. 13, 2018 5:11 pm

Birds, sorry I forgot to check. I just looked and had zero luck. i found some parts for the stove but not that one. eurostoves was the site that used to have most the parts but not much now and its a tough site to search. They dont seem to make parts for any of these foreign stoves for any length of time. I did look on 2 of the major site in the US too, and nestor martins website.

If it ends out helping at all my stove is the same as the Harmony 3, (they have a wood model too with that name), Bayard 312, and Montana. The only difference was the top piece. These stoves are listed as the following brands... Efel, Nestor Martin, and Surdiac.

You may have to have one made as Fred mentioned. Sorry I didnt have any luck and had forgotten to look before now.

birdsfan
New Member
Posts: 4
Joined: Mon. Feb. 26, 2018 2:49 pm
Hand Fed Coal Stove: Efel Arden
Coal Size/Type: Pea/Nut mix Anthracite from the Mammoth Vein
Stove/Furnace Make: EFEL
Stove/Furnace Model: ARDEN 084.65
Location: NEPA

Post By: birdsfan » Fri. Mar. 23, 2018 7:06 pm

Thanks warm. I am going to run a couple weld beads on my old shaker tool. The ol hook works just not as smoothly.

Post Reply

Return to “Imported Hand Fired Coal Stoves Using Anthracite”