Blacksmithing coal
-
- New Member
- Posts: 9
- Joined: Fri. Feb. 15, 2019 12:30 pm
Hello my new friends! My name is Brando Vanschoyck, I am from southeastern kentucky, hindman kentucky to be exact. I own and operate a small traditional blacksmithing business here in hindman called Deathless Forge. I am new to coal forging, I need some coal for blacksmithing. My mentor says that I need metallurgical coal, low sulfur, low ash high BTU and coal that cokes up. I am using some that he gave me, I think he may have said it was red onion? I am looking for a source of coal somewhat close to me that would sell me small quantities such as a pickup truck bed full of coal at a time. I would appreciate all help and suggestions, and I am here to learn! Thanks so much for your help!
Brando Vanschoyck
Brando Vanschoyck
-
- New Member
- Posts: 9
- Joined: Fri. Feb. 15, 2019 12:30 pm
Anyone ? Any advice at all is helpful and appreciated
-
- Member
- Posts: 2344
- Joined: Wed. Feb. 04, 2009 7:13 am
- Location: Fair Haven, VT
- Stoker Coal Boiler: Hybrid Axeman Anderson 130
- Baseburners & Antiques: Sparkle #12
- Coal Size/Type: Pea, Buckwheat, Nut
- Other Heating: LP Hot air. WA TX for coal use.
Not many folks here from that area but I'll give you a bump so your thread doesn't get lost in the fold. Someone may have your information and it's Saturday...hang in there.
-
- New Member
- Posts: 9
- Joined: Fri. Feb. 15, 2019 12:30 pm
Thank you very much my friend! I definitely need coal and a steady supply! Gas forges just wont cut it on certain projects, especially demonstrations and reenactments!! I really appreciate your time!
- warminmn
- Member
- Posts: 8208
- Joined: Tue. Feb. 08, 2011 5:59 pm
- Location: Land of 11,842 lakes
- Hand Fed Coal Stove: Chubby Junior, Riteway 37
- Coal Size/Type: nut and stove anthracite, lignite
- Other Heating: Wood and wear a wool shirt
Im not a blacksmith. I think Blaschak sells bags of what they call Blacksmith coal. Im guessing that is some form of hard coal but am uncertain. There is another company but the name escapes me that also sells bagged coal for blacksmithing. You might be able to buy small amounts, like a bag or two and pay a large shipping fee to try different brands before getting a truck load.
Check craigslist, facebook marketplace, etc, as you might find a local source. Im betting every setup will be different for what coal works best so i wouldnt buy tons of it before trying it. Good luck in your search and with your business.
Check craigslist, facebook marketplace, etc, as you might find a local source. Im betting every setup will be different for what coal works best so i wouldnt buy tons of it before trying it. Good luck in your search and with your business.
- BunkerdCaddis
- Member
- Posts: 708
- Joined: Sun. Jan. 18, 2015 10:26 am
- Location: SW Lancaster County
- Stoker Coal Boiler: Bairmatic-Van Wert
- Hand Fed Coal Boiler: Van Wert VW85H
- Hand Fed Coal Stove: Saey Hanover II working when I feel the desire, Waterford 105 out on vacation, Surdiac Gotha hiding somewhere
- Coal Size/Type: pea/nut/rice/stove-anthracite, nut/stove bit when I feel the urge
- Other Heating: oil fired hydronic
Did you do a search on blacksmithing on the forum? You did post in a "heating" thread... but try using the search bar in the upper right corner, chances are your question has been asked before but in a different thread. You could also browse the general interest threads here >>> General Interests
-
- New Member
- Posts: 9
- Joined: Fri. Feb. 15, 2019 12:30 pm
Thanks for the advice guys! When I searched blacksmithing on this forum all I found were posts that were 3 or 4 years old. As far as ordering online, the coal they sell from blacksmithing sites is called bituminous coal, and I think it is more specifically pocahontas coal, I believe from virginia or west virginia. The coal from hardware stores is anthracite and it doesnt work well at all for blacksmithing. I need coal that cokes up. If i order online it comes out to around a dollar a pound after shipping. I go through probably a 5 gallon bucket or so in 2 days maybe more. Thanks again.
- warminmn
- Member
- Posts: 8208
- Joined: Tue. Feb. 08, 2011 5:59 pm
- Location: Land of 11,842 lakes
- Hand Fed Coal Stove: Chubby Junior, Riteway 37
- Coal Size/Type: nut and stove anthracite, lignite
- Other Heating: Wood and wear a wool shirt
Around me, more of the Tractor Supply coal sells to blacksmiths than for heating and thats anthracite. Maybe watch some videos online on using anthracite and get it from a local TSC. If your set on using bit coal, ordering by the pallet (a ton or 2400 pounds, it varies) and shipping thru U-ship or fastenal shipping may be your best bet as far as ordering.
You should be close enough to a source to possibly buy in bulk but I couldnt tell you what mines. Perhaps talk to a couple coal dealers within a couple hundred miles and they may know where. Those steam engine folks may also know somewhere.
You should be close enough to a source to possibly buy in bulk but I couldnt tell you what mines. Perhaps talk to a couple coal dealers within a couple hundred miles and they may know where. Those steam engine folks may also know somewhere.
-
- New Member
- Posts: 18
- Joined: Sun. Dec. 30, 2018 4:26 am
- Location: Birmingham, AL
I'd definitely try some of that pocohontas though. Stuff is supposed to be legendary for smithing.
- BunkerdCaddis
- Member
- Posts: 708
- Joined: Sun. Jan. 18, 2015 10:26 am
- Location: SW Lancaster County
- Stoker Coal Boiler: Bairmatic-Van Wert
- Hand Fed Coal Boiler: Van Wert VW85H
- Hand Fed Coal Stove: Saey Hanover II working when I feel the desire, Waterford 105 out on vacation, Surdiac Gotha hiding somewhere
- Coal Size/Type: pea/nut/rice/stove-anthracite, nut/stove bit when I feel the urge
- Other Heating: oil fired hydronic
I was trying to read up on the blacksmithing coal and from your description of needing a "coking" coal I wonder if this thread would help Bit Coal ... or this thread if this is the kind of coal you're looking for Where Do You Get Your Bituminous Coal and a Going Price?
-
- New Member
- Posts: 9
- Joined: Fri. Feb. 15, 2019 12:30 pm
Yes my mentor and father in law both told me that I need bituminous coal, sometimes called metallurgical coal as well! Thank all of you guys for your help. Also I have a lot of ppl offering to give me what they're calling "house coal", what is house coal?! Thanks again guys
-
- New Member
- Posts: 9
- Joined: Fri. Feb. 15, 2019 12:30 pm
That's exactly what I've heard around demonstrations and conferences. Now, where to get it?!?! Hmmmm...TheScrambler92 wrote: ↑Sun. Feb. 17, 2019 10:20 amI'd definitely try some of that pocohontas though. Stuff is supposed to be legendary for smithing.
- Rob R.
- Site Moderator
- Posts: 18009
- Joined: Fri. Dec. 28, 2007 4:26 pm
- Location: Chazy, NY
- Stoker Coal Boiler: EFM 520
- Hand Fed Coal Stove: Chubby Jr
http://www.penncoal.com/blacksmith-live-steam.html
If you are willing to pay for freight, I am sure these guys would send you a pallet or two.
If you are willing to pay for freight, I am sure these guys would send you a pallet or two.