New 2 burning coal

Post Reply
 
Myboys22
New Member
Posts: 5
Joined: Tue. Dec. 12, 2017 5:06 pm

Post by Myboys22 » Wed. Jan. 03, 2018 1:34 pm

I hve a shelter furnace tht burns coal and wood. I'm having 2 burn wood with coal 2 get my furnace hot, coal by itself will not cut it and it burns up real fast. I live n owensboro ky so my coal comes from Sampson coal which is good quality. I'm just lost at wht I'm doing wrong.

 
User avatar
McGiever
Member
Posts: 10130
Joined: Sun. May. 02, 2010 11:26 pm
Location: Junction of PA-OH-WV
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hand Fed Coal Boiler: BUCKET A DAY water heater
Hand Fed Coal Stove: Warm Morning 414A
Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
Other Heating: Ground Source Heat Pump and some Solar

Post by McGiever » Wed. Jan. 03, 2018 9:34 pm

Welcome here to the Coal Forum Nice hearing from Kentucky!

Coal doesn't need much air like the wood does. Your sending all the heat up the stack.
Cut your air way back and be patient...coal is super slow to react to changes.

 
Myboys22
New Member
Posts: 5
Joined: Tue. Dec. 12, 2017 5:06 pm

Post by Myboys22 » Thu. Jan. 04, 2018 12:47 am

Thnks I'll try tht will hunks work better cuz I use wht my manual calls 4 which nugget size coal. I hve a key damper on does tht matter been reading baros r the best.


 
Myboys22
New Member
Posts: 5
Joined: Tue. Dec. 12, 2017 5:06 pm

Post by Myboys22 » Thu. Jan. 04, 2018 12:52 am

Also is there a certain way 2 load so It doesn't lose heat. I ask bc whn I load my furnace won't run 4 like an hr thn it will but by tht time my house is losing heat b4 it can replenish

 
User avatar
coaledsweat
Site Moderator
Posts: 13763
Joined: Fri. Oct. 27, 2006 2:05 pm
Location: Guilford, Connecticut
Stoker Coal Boiler: Axeman Anderson 260M
Coal Size/Type: Pea

Post by coaledsweat » Thu. Jan. 04, 2018 6:11 am

Rev the fire up good before you shake and reload.

 
Myboys22
New Member
Posts: 5
Joined: Tue. Dec. 12, 2017 5:06 pm

Post by Myboys22 » Thu. Jan. 04, 2018 10:14 am

I do i hve a draft blower on it


 
User avatar
McGiever
Member
Posts: 10130
Joined: Sun. May. 02, 2010 11:26 pm
Location: Junction of PA-OH-WV
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hand Fed Coal Boiler: BUCKET A DAY water heater
Hand Fed Coal Stove: Warm Morning 414A
Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
Other Heating: Ground Source Heat Pump and some Solar

Post by McGiever » Thu. Jan. 04, 2018 9:22 pm

Myboys22 wrote:
Thu. Jan. 04, 2018 12:47 am
Thnks I'll try tht will hunks work better cuz I use wht my manual calls 4 which nugget size coal. I hve a key damper on does tht matter been reading baros r the best.
Some report hunks work very well, give them a try for sure.
Your key damper (MPD) will do fine if you don't have overly strong draft there.
Learning how best to use that key damper will determine how good you get make the fire do what you want it to do. ;)

 
User avatar
McGiever
Member
Posts: 10130
Joined: Sun. May. 02, 2010 11:26 pm
Location: Junction of PA-OH-WV
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hand Fed Coal Boiler: BUCKET A DAY water heater
Hand Fed Coal Stove: Warm Morning 414A
Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
Other Heating: Ground Source Heat Pump and some Solar

Post by McGiever » Thu. Jan. 04, 2018 9:25 pm

Myboys22 wrote:
Thu. Jan. 04, 2018 12:52 am
Also is there a certain way 2 load so It doesn't lose heat. I ask bc whn I load my furnace won't run 4 like an hr thn it will but by tht time my house is losing heat b4 it can replenish
This is where the key damper needs learned...be careful and don't leave it too open, plus you would want to be sure and let some top air in for a while to burn off the gases produced above the fire after reload time.

 
Myboys22
New Member
Posts: 5
Joined: Tue. Dec. 12, 2017 5:06 pm

Post by Myboys22 » Fri. Jan. 05, 2018 1:28 am

I think thts my problem is tht draft is 2 strong once it gets going good bc whn I burn the wood and coal together the flames still move fast like it's getting air. Will coal burn with all the air cut off or will it go out. I wanna try shutting the draft knob all the way whn it gets going but dnt wanna kill it

Post Reply

Return to “Bituminous Coal Heating General Topics”