Putting my AA130 to use
- Lightning
- Site Moderator
- Posts: 14652
- Joined: Wed. Nov. 16, 2011 9:51 am
- Location: Olean, NY
- Stoker Coal Boiler: Modified AA 130
- Coal Size/Type: Pea Size - Anthracite
Just the boiler vessel isn't extremely heavy. If I had to guess, I'd give it 300-350 pounds maybe. Me and another guy slid mine down a ramp, which was a sheet of plywood over the basement stairs. Then I was able to get it into position and hoist it up by myself. Once suspended, I just slid the base underneath and lowered the boiler vessel on. It all went pretty smoothly lol.
Is that a picture of it in your basement?
Is that a picture of it in your basement?
- Retro_Origin
- Member
- Posts: 900
- Joined: Sun. Feb. 21, 2021 7:46 pm
- Location: Schuylkill county
- Stoker Coal Boiler: 1957 Axeman Anderson 130
- Coal Size/Type: Buckwheat / Pea
Neighbor has an engine hoist I can borrow, I'll just put it in a heavy duty cart and wheel it to the bilco doors, then back with the engine hoist lower it down onto the cart and then I can probably fit the engine hoist in the basement and put it on blocks till I can paint it.Lightning wrote: ↑Mon. Nov. 07, 2022 4:30 pmJust the boiler vessel isn't extremely heavy. If I had to guess, I'd give it 300-350 pounds maybe. Me and another guy slid mine down a ramp, which was a sheet of plywood over the basement stairs. Then I was able to get it into position and hoist it up by myself. Once suspended, I just slid the base underneath and lowered the boiler vessel on. It all went pretty smoothly lol.
Is that a picture of it in your basement?
SO, that's a picture of the chicken house, there's a roof leak a few feet away from where the boiler sat so there was a good amount of moisture there. I didn't see much rust at all in the base, looked really good. I think someone painted and restored the whole thing in the past 5-10 years. I actually contemplated just putting it back together and screwing the paint job....but knew I'd never forgive myself.
- Retro_Origin
- Member
- Posts: 900
- Joined: Sun. Feb. 21, 2021 7:46 pm
- Location: Schuylkill county
- Stoker Coal Boiler: 1957 Axeman Anderson 130
- Coal Size/Type: Buckwheat / Pea
So I told my wife that all I want for Christmas is to have the axeman online before the new year!
Finally got it down in the basement where it’s dry. Base got a quick paint job after wire wheeling and flap disc. The surface is pretty pocky and scaly from previous paint and corrosion. Thanks swyman for the color inspiration! Not too worried about it since inside looks great with no heavy flaking or breakthrough areas.
Really wanted to get this inside so I could try to flush out some of the sludge. From carrying it down we had some gook spill out. I take it this is one more reason why to pull water from the top of the boiler, however I’m seeing some streaks/sludge skidding in my radiant tubing, not sure if this is coming from the keystoker or what..but I don't like it! Is this something I should have an in-line screen for? Took the garden hose in through the coil opening and really blasted it. I’m impressed how clean and smooth the burn chamber surfaces are.
Have the motor and fan assembly strapped to basement post so doesn’t leak and the fan plate is screwed to it so it doesn’t bear on the shaft. This motor is pretty old, can someone suggest an off the shelf replacement? Wish I could use a 1/6th hp oil burner motor because I have a brand new one! Had a stud previously broke that still leaked after I did a partial fix for my chicken house run. Made a drill bushing that fit exactly in the coil plate with the tap drill size as the Id. Had coil plate in place during drilling, this way when I turn the stud threads it will match up with the 1/2" hole in the coil plate. (1/8-27 npt into boiler wall)
Finally got it down in the basement where it’s dry. Base got a quick paint job after wire wheeling and flap disc. The surface is pretty pocky and scaly from previous paint and corrosion. Thanks swyman for the color inspiration! Not too worried about it since inside looks great with no heavy flaking or breakthrough areas.
Really wanted to get this inside so I could try to flush out some of the sludge. From carrying it down we had some gook spill out. I take it this is one more reason why to pull water from the top of the boiler, however I’m seeing some streaks/sludge skidding in my radiant tubing, not sure if this is coming from the keystoker or what..but I don't like it! Is this something I should have an in-line screen for? Took the garden hose in through the coil opening and really blasted it. I’m impressed how clean and smooth the burn chamber surfaces are.
Have the motor and fan assembly strapped to basement post so doesn’t leak and the fan plate is screwed to it so it doesn’t bear on the shaft. This motor is pretty old, can someone suggest an off the shelf replacement? Wish I could use a 1/6th hp oil burner motor because I have a brand new one! Had a stud previously broke that still leaked after I did a partial fix for my chicken house run. Made a drill bushing that fit exactly in the coil plate with the tap drill size as the Id. Had coil plate in place during drilling, this way when I turn the stud threads it will match up with the 1/2" hole in the coil plate. (1/8-27 npt into boiler wall)
Attachments
- StokerDon
- Site Moderator
- Posts: 7484
- Joined: Mon. Nov. 11, 2013 11:17 am
- Location: PA, Southern York County!
- Stoker Coal Boiler: Gentleman Janitor GJ-5, Van Wert VA-600, Axeman Anderson130 X3.
- Hand Fed Coal Furnace: Harman SF3500 reduced down to 3 grates connected to its own plenum
- Coal Size/Type: Rice, Chestnut and whatever will fit through the door on the Harman
- Other Heating: Noth'in but COAL! Well, Maybe a little tiny bit of wood
Another Copper Colored Coal Burn'in Contraption!!!
If you are worried about gunk getting into your system from the old rusty boiler, you could put a Wye strainer in line. That will catch the big chunks.
You better get that thing fired up. Its coal out!
-Don
If you are worried about gunk getting into your system from the old rusty boiler, you could put a Wye strainer in line. That will catch the big chunks.
You better get that thing fired up. Its coal out!
-Don
- Retro_Origin
- Member
- Posts: 900
- Joined: Sun. Feb. 21, 2021 7:46 pm
- Location: Schuylkill county
- Stoker Coal Boiler: 1957 Axeman Anderson 130
- Coal Size/Type: Buckwheat / Pea
Drilling out stud with plate and bushing in place for lineup
Tapping 1/8-27
Install stud with plate in place
Room to tighten more or weld it would spring a leak!
- Retro_Origin
- Member
- Posts: 900
- Joined: Sun. Feb. 21, 2021 7:46 pm
- Location: Schuylkill county
- Stoker Coal Boiler: 1957 Axeman Anderson 130
- Coal Size/Type: Buckwheat / Pea
Fully painted!
Basement paint booth
Highly effective ventilation to prevent spouse irritation
Base placed!
Ready for the flop!
- Retro_Origin
- Member
- Posts: 900
- Joined: Sun. Feb. 21, 2021 7:46 pm
- Location: Schuylkill county
- Stoker Coal Boiler: 1957 Axeman Anderson 130
- Coal Size/Type: Buckwheat / Pea
Flip and flop all by myself!
When I flipped it I heard a jangle.....looks like either these pieces were left in from assembly or some sort of repair was done and they couldn’t get the remnants out! Not crazy about it but hey it looks great and hasn’t leaked!
When I flipped it I heard a jangle.....looks like either these pieces were left in from assembly or some sort of repair was done and they couldn’t get the remnants out! Not crazy about it but hey it looks great and hasn’t leaked!
- StokerDon
- Site Moderator
- Posts: 7484
- Joined: Mon. Nov. 11, 2013 11:17 am
- Location: PA, Southern York County!
- Stoker Coal Boiler: Gentleman Janitor GJ-5, Van Wert VA-600, Axeman Anderson130 X3.
- Hand Fed Coal Furnace: Harman SF3500 reduced down to 3 grates connected to its own plenum
- Coal Size/Type: Rice, Chestnut and whatever will fit through the door on the Harman
- Other Heating: Noth'in but COAL! Well, Maybe a little tiny bit of wood
Nice!
Just a few pipes away from firing it up! Love the "Instant Paint Booth"!
Just a few pipes away from firing it up! Love the "Instant Paint Booth"!
- Retro_Origin
- Member
- Posts: 900
- Joined: Sun. Feb. 21, 2021 7:46 pm
- Location: Schuylkill county
- Stoker Coal Boiler: 1957 Axeman Anderson 130
- Coal Size/Type: Buckwheat / Pea
Seriously! Everything works just a matter of pipes! I had to shim the base to keep the thing level, about 3/4 on one side, should I fill in the air gap with something? What would be best? wasn't really interested in doing pavers with grout on the floor...
- StokerDon
- Site Moderator
- Posts: 7484
- Joined: Mon. Nov. 11, 2013 11:17 am
- Location: PA, Southern York County!
- Stoker Coal Boiler: Gentleman Janitor GJ-5, Van Wert VA-600, Axeman Anderson130 X3.
- Hand Fed Coal Furnace: Harman SF3500 reduced down to 3 grates connected to its own plenum
- Coal Size/Type: Rice, Chestnut and whatever will fit through the door on the Harman
- Other Heating: Noth'in but COAL! Well, Maybe a little tiny bit of wood
Most people use a small, self leveling concreate pad to set it on. That is probably the best way to get it level.Retro_Origin wrote: ↑Sat. Dec. 10, 2022 7:42 pmSeriously! Everything works just a matter of pipes! I had to shim the base to keep the thing level, about 3/4 on one side, should I fill in the air gap with something? What would be best? wasn't really interested in doing pavers with grout on the floor...
You don't really need to seal the base to the floor, but keep in mind that flyash will constantly leak out of the gaps.
That reminds me, I didn't seal mine yet.
-Don