Burning Coal in a Wood Stove?

 
cookies4meq
New Member
Posts: 1
Joined: Sun. Nov. 15, 2009 8:26 pm

Post by cookies4meq » Sun. Nov. 15, 2009 8:51 pm

We have a Fisher woodburning stove. Old model. Can I burn coal in that stove or does it get too hot?
I am tired of cutting wood and it's getting harder to find as my area turns more suburban every year.


 
User avatar
lowfog01
Member
Posts: 3889
Joined: Sat. Dec. 20, 2008 8:33 am
Location: Springfield, VA
Hand Fed Coal Stove: Mark II & Mark I
Coal Size/Type: nut/pea

Post by lowfog01 » Sun. Nov. 15, 2009 9:05 pm

It depends - was your stove originally designed to burn both wood and coal. Typically, you can burn wood in a coal stove but can't burn coal in a wood stove. Coal needs an under fire source of draft to burn and a set of shaker grates so you can clear the ash periodically. Does your stove have these things? A coal stove will also have fire bricks inside. The under fire air source will be a dial or a slide bar on the lower half of the stove. It may also be on the ash pan door. A Coal stove will have an exterior shaker arm of some sort for you to shake the grates. If you do not have these two things or know of a kit which you can use to add them your wood stove will not burn coal. You probably can find the answers to these questions in your stove's user manual or on line. Good Luck, Lisa

 
User avatar
rockwood
Member
Posts: 1381
Joined: Sun. Sep. 21, 2008 7:37 pm
Location: Utah
Hot Air Coal Stoker Furnace: Stokermatic
Hand Fed Coal Stove: Rockwood Stoveworks Circulator
Baseburners & Antiques: Malleable/Monarch Range
Coal Size/Type: Lump and stoker + Blaschak-stove size

Post by rockwood » Sun. Nov. 15, 2009 10:22 pm

cookies4meq wrote:Can I burn coal in that stove or does it get too hot?
About the only coal you can burn in a stove like that is lump soft coal (large bituminous pieces of coal) and it's still going to be a pain getting the ashes out if you keep the fire going constantly. You can get a fireplace cast iron grate and set it in the stove but they don't last very long because ash builds up under them and they overheat and literally burn up in the fire. Like Lisa said grates, ash pit etc. is what you need for burning coal so I would look at replacing the woodstove with one designed to burn coal. As far as the stove getting too hot...it will only get too hot if you don't properly control the air/draft through the stove.

 
User avatar
CoalHeat
Member
Posts: 8862
Joined: Sat. Feb. 10, 2007 9:48 pm
Location: Stillwater, New Jersey
Stoker Coal Boiler: 1959 EFM 350
Hand Fed Coal Stove: Harman Magnafire Mark I
Baseburners & Antiques: Sears Signal Oak 15 & Andes Kitchen Range
Coal Size/Type: Rice and Chestnut
Other Heating: Fisher Fireplace Insert

Post by CoalHeat » Mon. Nov. 16, 2009 10:12 am

Welcome to the forum.

Sorry, can't burn coal in the Fisher, it's wood only. You need a grate and a way to feed air into the stove below the grate, as coal burns from the bottom up. I understand the firewood issue, I heated with wood using 2 stoves for 16 years. I still have the Fisher insert, still use it.

The amount of modifications involved to try to make it burn coal are extensive and with no guarantee it will work. Time to consider a coal burner! :D A good used coal stove can be found for a reasonable price.
FISHER 11-03-17.JPG
.JPG | 104.2KB | FISHER 11-03-17.JPG
There's a thread here about them:
Fisher Wood Stoves

Here's a Fisher manual if you need one:
fischermanual.pdf
.PDF | 682.4KB | fischermanual.pdf

 
smokeyCityTeacher
Member
Posts: 768
Joined: Mon. Oct. 19, 2009 10:41 pm
Location: Pittsburgh, PA
Hand Fed Coal Stove: Hitzer 30-95

Post by smokeyCityTeacher » Thu. Nov. 19, 2009 6:07 pm

cookies4meq wrote:We have a Fisher wood-burning stove. Old model. Can I burn coal in that stove or does it get too hot?
I am tired of cutting wood and it's getting harder to find as my area turns more suburban every year.
If you don't mind treating your wood stove as disposable -- and its located in an area that can't burn the house down then the answer is yes - you can burn anything you want.

Last winter I beat the crap out of my Vogelzang boxer by constantly over-firing it and tossing in big lumps of coal to sweeten the pot.

It constantly glowed cherry red as did the stack pipe. The coal was not burnt efficiently, but enough to put out probably 150K BTUs on some nights!

All the gaskets are cooked and now the stove leaks like a sieve.

Even damped all the way down is eating thru wood like cotton candy :=)

Its mind over matter. If you don't mind then it don't matter ... you can burn coal in a wood stove.

The real questions is *should you* - or should you go find a used coal stove and burn coal right.

.....I get a kick out of seeing my wood stove glowing like Rudolph's nose on Chirstmas eve.

 
ronzander1
New Member
Posts: 2
Joined: Wed. Jul. 27, 2016 3:31 pm
Other Heating: Fisher

Post by ronzander1 » Wed. Jul. 27, 2016 3:35 pm

I had to laugh at the Post saying you can't burn coal in a Fisher stove. We have one in our cabin and the family has been doing that for over 40 yrs without incident, and even funnier is the fact that they posted a link to a Fisher manual that clearly tells you how to burn coal in those stoves on page 15? Hilarious...!!!

 
coalnewbie
Member
Posts: 8601
Joined: Sat. May. 24, 2008 4:26 pm
Location: Chester, NY
Hot Air Coal Stoker Stove: LL AnthraKing 180K, Pocono110K,KStokr 90K, DVC
Hand Fed Coal Stove: Invader 2
Baseburners & Antiques: Wings Best, Glenwood #8(x2) Herald 116x
Coal Size/Type: Rice,
Other Heating: Heating Oil CH, Toyotomi OM 22

Post by coalnewbie » Wed. Jul. 27, 2016 3:51 pm

Hmmm, 2inch clearance and you spent 40 years doing that. You obviously like pain, do you own a horse farm.


 
User avatar
Lightning
Site Moderator
Posts: 14658
Joined: Wed. Nov. 16, 2011 9:51 am
Location: Olean, NY
Stoker Coal Boiler: Modified AA 130
Coal Size/Type: Pea Size - Anthracite

Post by Lightning » Wed. Jul. 27, 2016 4:14 pm

cookies4meq wrote:We have a Fisher woodburning stove. Old model. Can I burn coal in that stove or does it get too hot?
I am tired of cutting wood and it's getting harder to find as my area turns more suburban every year.
It depends on what type of coal. As mentioned, big chunks of bituminous on top of a wood fire will work if it doesn't have a source for under fire air.

Anthracite needs under fire air to burn efficiently and effectively.

With both types you do need a shaker grate system to clear ash. Wood is only 1-2% ash. Coal is 10-15% ash (by weight). Ash needs to be cleared from the fuel bed at least once or up to 3 times per day or it will choke out the fire.

 
User avatar
coaledsweat
Site Moderator
Posts: 13763
Joined: Fri. Oct. 27, 2006 2:05 pm
Location: Guilford, Connecticut
Stoker Coal Boiler: Axeman Anderson 260M
Coal Size/Type: Pea

Post by coaledsweat » Wed. Jul. 27, 2016 7:17 pm

Looking at the Fisher site shows two multifuel models, I believe the Charlston and the Denniston were the names of the stoves.

Just checked the manual and it says only sub bituminous. Anthracite isn't going to work.

 
User avatar
freetown fred
Member
Posts: 30293
Joined: Thu. Dec. 31, 2009 12:33 pm
Location: Freetown,NY 13803
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut

Post by freetown fred » Wed. Jul. 27, 2016 7:48 pm

I guess I was thinkin you could of shared your experience & methods burning in the Fisher. Guess you were to busy laughin?? Wouldn't hurt to complete fillin out your profile--promise, nobodies gonna steal ya.
ronzander1 wrote:I had to laugh at the Post saying you can't burn coal in a Fisher stove. We have one in our cabin and the family has been doing that for over 40 yrs without incident, and even funnier is the fact that they posted a link to a Fisher manual that clearly tells you how to burn coal in those stoves on page 15? Hilarious...!!!

 
User avatar
warminmn
Member
Posts: 8108
Joined: Tue. Feb. 08, 2011 5:59 pm
Location: Land of 11,842 lakes
Hand Fed Coal Stove: Chubby Junior, Efel Nestor Martin, Riteway 37
Coal Size/Type: nut and stove anthracite, lignite
Other Heating: Wood and wear a wool shirt

Post by warminmn » Wed. Jul. 27, 2016 10:07 pm

coaledsweat wrote:Looking at the Fisher site shows two multifuel models, I believe the Charlston and the Denniston were the names of the stoves.

Just checked the manual and it says only sub bituminous. Anthracite isn't going to work.
The Fisher model Im thinking of is called "coal bear". Kind of rare. I remember looking at pics and thinking it wouldnt be a great ant coal stove but would work, and be an decent dual fuel. A nice looking stove too. Fisher kept millions of people warm with their stoves of various designs at a reasonable price.

yes Ronzander, please give us some insight into how you made it work. We are all here to learn from each other.

 
ronzander1
New Member
Posts: 2
Joined: Wed. Jul. 27, 2016 3:31 pm
Other Heating: Fisher

Post by ronzander1 » Sat. Jul. 30, 2016 12:15 pm

Well, for the first thing we don't load it full of coal...but rather after building a nice wood fire we simply add 5-6 nice size chunks of good old black shiny wyoming coal (bigger than your fist, smaller than your head) and I'll add that our stove is in our cabin in Wyoming (and at 8500 ft alt where it can be 45F in the morning even in August...and this stove is only heat source) and contrary to all the horror stories, the stove isn't warped, its never turned glowing red, nor has anyone died of carbon monoxide either...and that despite having burned literally tons of coal over the years. This tove then keeps the entire place warm all night long and in the morning we have nice banked coals in there buried in the ashes that take at most a piece of newspaper to get then get some added wood burning to cook our breakfast. While I'm sure someone, someplace, and at sometime, has managed to burn their house down, ruined their stove, or had some bad experience, my inclination would be they likely were not all that bright...like most of the posters here obviously. Apparently most of those who replied have way too much time on your hands, or you simply got up and had your morning cup of azzhole before responding (based on the sarcastic and who the f**k are you to comment on our posts...attitudes that were hard to miss in several of those replies) and while I don't now...I did once own a horse farm (had a thoroughbred stallion & six mares...lots new babies each year) and I'm still laughing! I should add a "thank you" for the nice welcome to the board...and hope some of you get a real life one day...it's a big world out there and you may want to explore it and unless your happy simply mirroring the majority of the people out there these days...who in general must be from IOWA (Idiots Out Wandering Around) and oblivious to the fact that they really don't know sh*t about much of anything...which is generally revealed by their typical propensity to incessantly blabber online...and usually about things they are clueless about. So, that's more words than was necessary I guess...as a simple FYI (fu*k you idiots) would have sufficedhere, but do have a nice day!

 
User avatar
StokerDon
Site Moderator
Posts: 7486
Joined: Mon. Nov. 11, 2013 11:17 am
Location: PA, Southern York County!
Stoker Coal Boiler: Gentleman Janitor GJ-5, Van Wert VA-600, Axeman Anderson130 X3.
Hand Fed Coal Furnace: Harman SF3500 reduced down to 3 grates connected to its own plenum
Coal Size/Type: Rice, Chestnut and whatever will fit through the door on the Harman
Other Heating: Noth'in but COAL! Well, Maybe a little tiny bit of wood

Post by StokerDon » Sat. Jul. 30, 2016 1:19 pm

Since your not going to answer the real question here, I'll do it for you so in the future other people reading this thread will understand.

The Fisher wood stove is apparently very good at burning sub-bituminous coal and will put out a great amount of heat. It will not work very well if you try to burn anthracite coal.

I'm glad your Fisher works for your situation and I wish you many more years of reliable service. Some of us get a little to caught up in the details, but really we are all just trying to keep our families warm for the least amount of money.

-Don

 
coalnewbie
Member
Posts: 8601
Joined: Sat. May. 24, 2008 4:26 pm
Location: Chester, NY
Hot Air Coal Stoker Stove: LL AnthraKing 180K, Pocono110K,KStokr 90K, DVC
Hand Fed Coal Stove: Invader 2
Baseburners & Antiques: Wings Best, Glenwood #8(x2) Herald 116x
Coal Size/Type: Rice,
Other Heating: Heating Oil CH, Toyotomi OM 22

Post by coalnewbie » Sat. Jul. 30, 2016 1:26 pm

IOWA (Idiots Out Wandering Around)
I like that one :D where is IOWA?
and oblivious to the fact that they really don't know sh*t about much of anything...which is generally revealed by their typical propensity to incessantly blabber online
You leave FF out of this, he is my friend ..... hahahahahhaa, damn I broke another rib. I am a riot.

Your refreshing comments are somewhat direct for us sensitive lads on the East coast .... hahahahhahahaha but you are very entertaining. Thx for your input.

 
User avatar
warminmn
Member
Posts: 8108
Joined: Tue. Feb. 08, 2011 5:59 pm
Location: Land of 11,842 lakes
Hand Fed Coal Stove: Chubby Junior, Efel Nestor Martin, Riteway 37
Coal Size/Type: nut and stove anthracite, lignite
Other Heating: Wood and wear a wool shirt

Post by warminmn » Sat. Jul. 30, 2016 1:33 pm

There are very few people on this site that burn that type of coal. Maybe our Alaskan friends do, and some lignite burners. And thanks for the friendly comments. I can tell we will learn a lot from you :lol:


Post Reply

Return to “Wood, Pellets, Gas, Oil, Geothermal & Other Heating Types”