Starting the Stanley Argand-Video

wsherrick · Post by **wsherrick** » Mon. Feb. 09, 2009 12:34 am

Part 1
[youtube]https://www.youtube.com/watch?v=_Mm39rZNFtI [/youtube]

Part 2

Part 3

Here is a series of videos on how I start up my Stanley Argand Parlor Stove. I thought it would be interesting for everyone to compare the old stoves to the new ones in the methods used to operate them. I stutter and stammer a little bit, but; I hope I get the point across. I hope you enjoy them. It took me long enough to figure out how to do all of this video stuff.

Freddy · Post by **Freddy** » Mon. Feb. 09, 2009 4:26 am

Beautiful job. Not only making the video, but making fire! Everything we read says to let the wood burn down to glowing embers before adding coal, but just recently I was taught my a hand stove friend to throw in a couple handfuls of coal even before lighting, then as you, once the fire is going, add coal. Just make sure to leave plenty of room for air, draft, flame.

Devil505 · Post by **Devil505** » Mon. Feb. 09, 2009 7:24 am

Nice job!

Like Freddy says too, I always start the coal as soon as the wood fire is roaring, like 1 minute after lighting. The only thing you have to be careful of is not putting in some much coal that you smother the fire. Waiting until the wood fire burns to embers is not necessary & adds about an hour to the lighting process.

Ashcat · Post by **Ashcat** » Mon. Feb. 09, 2009 2:26 pm

Well done! Good job on the video and it's great to see a classic stove in operation.

wsherrick · Post by **wsherrick** » Mon. Feb. 09, 2009 11:57 pm

Thanks for the compliments guys! When I light the stove using those small, lower doors (quick start doors) even a big charge of coal will quickly ignite. You'll know it in a hurry if you forget to close those little doors all the way. The thing you have to be careful about is to make sure that the draft adjustments are made BEFORE the coal becomes totally lit so you don't overfire the stove. Another thing I watch is heating it up too quickly from a cold start. I don't want to cause too much thermal stress on it so once it is going I nip it back to allow the stove to heat up at an even pace.

jackpine · Post by **jackpine** » Tue. Feb. 10, 2009 10:56 am

Great video...well done.

I have burned wood for years. Lately I have experimented firing coal in a cookstove.This video encourages me even more to either find a old coal baseburner or locate a coal grate, stove liner and magazine for a Round Oak cylinder stove.

Jackpine

wsherrick · Post by **wsherrick** » Thu. Mar. 05, 2009 11:58 pm

Sorry guys, I tried to add a couple more videos about shaking the grates and reviving the fire, but; I didn't have much success. I will try again tomorrow I guess.

Devil505 · Post by **Devil505** » Fri. Mar. 06, 2009 6:28 am

wsherrick wrote:Sorry guys, I tried to add a couple more videos about shaking the grates and reviving the fire, but; I didn't have much success. I will try again tomorrow I guess.

How large an area do you heat with that?

wsherrick · Post by **wsherrick** » Fri. Mar. 06, 2009 4:15 pm

Devil505 wrote:
wsherrick wrote:Sorry guys, I tried to add a couple more videos about shaking the grates and reviving the fire, but; I didn't have much success. I will try again tomorrow I guess.
How large an area do you heat with that?

The house is about 1500 square feet. This stove can really crank out the heat for its size. Even when it is below zero the main living areas are well above 70 and the bedrooms are a little bit cooler, down in the mid to upper 60's. When the temperatures are in the upper 20's and 30's if you open it up a little it will run you out of there.

wsherrick · Post by **wsherrick** » Fri. Mar. 06, 2009 4:16 pm

Here is part four about shaking the fire. There are two more short parts I will try to add.

Here is part five. Below is part six.

9mmruger · Post by **9mmruger** » Sat. Mar. 07, 2009 5:39 am

Thanks so much for the vid. Was great to watch. Enjoyed it muchly.

009to090 · Post by **009to090** » Sat. Mar. 07, 2009 9:11 am

William,
thanks for the great videos! Very informative!
Nice stove, too!

wsherrick · Post by **wsherrick** » Sun. Mar. 08, 2009 7:33 pm

Thanks I hoped these videos would help those who were just starting out and who want to find out about coal to see if they want to make it a part of their lives like we all have. If anyone thinks I left out anything important or has any questions, let me know.
In the last video I meant to say,"Goodbye and happy heating with your coal stove;" but, I forgot it at the end. So I will say it now. HAPPY HEATING TO ALL.