Is there a proper way?

Post Reply
 
User avatar
viper98gts
Member
Posts: 28
Joined: Wed. Jul. 31, 2013 8:54 am
Location: Geneva Ohio
Stoker Coal Boiler: Keystoker Ka6 dual fuel
Hand Fed Coal Stove: Hitzer 50-93
Baseburners & Antiques: Germer NO 17. Base burner. Glenwood no.8 base heater

Post by viper98gts » Fri. Mar. 17, 2023 3:43 pm

Is there a proper way to fasten the spark guard in the Glenwood no.8?
What did the factory use?

Attachments

20230301_133304.jpg
.JPG | 628.9KB | 20230301_133304.jpg

 
User avatar
Sunny Boy
Member
Posts: 25560
Joined: Mon. Nov. 11, 2013 1:40 pm
Location: Central NY
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace

Post by Sunny Boy » Fri. Mar. 17, 2023 4:56 pm

Likely they just dropped in a cotter pin at each end. It was a common fastener back then.

Paul

 
User avatar
viper98gts
Member
Posts: 28
Joined: Wed. Jul. 31, 2013 8:54 am
Location: Geneva Ohio
Stoker Coal Boiler: Keystoker Ka6 dual fuel
Hand Fed Coal Stove: Hitzer 50-93
Baseburners & Antiques: Germer NO 17. Base burner. Glenwood no.8 base heater

Post by viper98gts » Sat. Mar. 18, 2023 8:22 am

I just got a recast replacement from Wilson (nice piece btw) and I don't want it to fall off and get broken.
The only thing that I could get to fit thru the hole is a 1/8 in. stainless rivet. Do you think that would hold up under the heat?


 
User avatar
Sunny Boy
Member
Posts: 25560
Joined: Mon. Nov. 11, 2013 1:40 pm
Location: Central NY
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace

Post by Sunny Boy » Sat. Mar. 18, 2023 8:38 am

viper98gts wrote:
Sat. Mar. 18, 2023 8:22 am
I just got a recast replacement from Wilson (nice piece btw) and I don't want it to fall off and get broken.
The only thing that I could get to fit thru the hole is a 1/8 in. stainless rivet. Do you think that would hold up under the heat?
As long as you don't overfill the firepot, up where that grill is it isn't hot enough to melt even mild steel. I have plain steel cotter pins holding the grill in my GW #6. The rivets should work also.

Paul

 
User avatar
viper98gts
Member
Posts: 28
Joined: Wed. Jul. 31, 2013 8:54 am
Location: Geneva Ohio
Stoker Coal Boiler: Keystoker Ka6 dual fuel
Hand Fed Coal Stove: Hitzer 50-93
Baseburners & Antiques: Germer NO 17. Base burner. Glenwood no.8 base heater

Post by viper98gts » Sat. Mar. 18, 2023 5:19 pm

Okay, thank you Paul

Post Reply

Return to “Antiques, Baseburners, Kitchen Stoves, Restorations & Modern Reproductions”