OUR BEST Base Burner
-
- Member
- Posts: 303
- Joined: Thu. Jan. 20, 2011 8:12 am
- Stoker Coal Boiler: Van Wert 600
- Hand Fed Coal Boiler: Tarm 202
- Hand Fed Coal Stove: Harman HXL, 150, Crane 88, Crane 404
- Other Heating: Solar
Got this today. All parts complete. I do have the bottom w/air diffusers and the original cast 90 el w/ air adjust for the base exhaust.
Previous owner said he got it from Barnstable stove shop, and never hooked it up or lit it. It appears to be a complete tear down and rebuild. The re lining of pot dims are 13 inch dia, and 12 inch height, so #'s mean approx. 40 Pounds plus burn pot. I am excited to see how these burn.
Any hints on how to get the stove on its bottom base, alone? Or just find a second person.
Also , should I leave the air diffusers alone , or I can sand blast them and silver heat paint them. I need to slow cook any ideas of changing some thing this old. thanks, r
Previous owner said he got it from Barnstable stove shop, and never hooked it up or lit it. It appears to be a complete tear down and rebuild. The re lining of pot dims are 13 inch dia, and 12 inch height, so #'s mean approx. 40 Pounds plus burn pot. I am excited to see how these burn.
Any hints on how to get the stove on its bottom base, alone? Or just find a second person.
Also , should I leave the air diffusers alone , or I can sand blast them and silver heat paint them. I need to slow cook any ideas of changing some thing this old. thanks, r
Attachments
-
- Member
- Posts: 303
- Joined: Thu. Jan. 20, 2011 8:12 am
- Stoker Coal Boiler: Van Wert 600
- Hand Fed Coal Boiler: Tarm 202
- Hand Fed Coal Stove: Harman HXL, 150, Crane 88, Crane 404
- Other Heating: Solar
OUR BEST Base Burner No. 116X
Leonard and Baker Stove Co.
Taunton , Mass
Leonard and Baker Stove Co.
Taunton , Mass
-
- Member
- Posts: 303
- Joined: Thu. Jan. 20, 2011 8:12 am
- Stoker Coal Boiler: Van Wert 600
- Hand Fed Coal Boiler: Tarm 202
- Hand Fed Coal Stove: Harman HXL, 150, Crane 88, Crane 404
- Other Heating: Solar
Also, very possible new sheet steel body from the Barnstable shop. A few of the paint scrapes show a newer galv steel color underneath.
- Sunny Boy
- Member
- Posts: 25729
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Congrats on a very good base heater.
If need be, you can put the stove on it's base by yourself, if you have a lot of scrap pieces of boards by using the tilt-jack method. I've done this with my kitchen range - which is much heavier than your base heater. And I used the same method for my Glenwood #6, which is a twin of your Wings Best.
Remove everything possible to lighten the stove - including slide the grates and frame out.
Put the leg base where you want the stove to be.
Walk the stove onto a small rug and drag the stove next to the leg base.
Tilt the stove just enough to slip a board under one of the sides of the base pan.
Tilt it the opposite way and put a board under that side.
Keep tilting and placing boards until the stove's base pan is the same hieght as the leg base top edge.
Tilt the stove forward and place a longer board from the two stacks of boards over onto and across the base.
Tilt the stove backwards and slip another long board from stacks to leg base.
Gently rock and walk the stove across onto the leg base. Tilt and remove a long board and gently lower the stove onto the leg base making sure to align the edge overlap. Tilt the stove the other way and remove the last long board and again, be careful to align the edge overlap as you gently lower the stove onto the leg base.
Paul
If need be, you can put the stove on it's base by yourself, if you have a lot of scrap pieces of boards by using the tilt-jack method. I've done this with my kitchen range - which is much heavier than your base heater. And I used the same method for my Glenwood #6, which is a twin of your Wings Best.
Remove everything possible to lighten the stove - including slide the grates and frame out.
Put the leg base where you want the stove to be.
Walk the stove onto a small rug and drag the stove next to the leg base.
Tilt the stove just enough to slip a board under one of the sides of the base pan.
Tilt it the opposite way and put a board under that side.
Keep tilting and placing boards until the stove's base pan is the same hieght as the leg base top edge.
Tilt the stove forward and place a longer board from the two stacks of boards over onto and across the base.
Tilt the stove backwards and slip another long board from stacks to leg base.
Gently rock and walk the stove across onto the leg base. Tilt and remove a long board and gently lower the stove onto the leg base making sure to align the edge overlap. Tilt the stove the other way and remove the last long board and again, be careful to align the edge overlap as you gently lower the stove onto the leg base.
Paul
-
- Member
- Posts: 303
- Joined: Thu. Jan. 20, 2011 8:12 am
- Stoker Coal Boiler: Van Wert 600
- Hand Fed Coal Boiler: Tarm 202
- Hand Fed Coal Stove: Harman HXL, 150, Crane 88, Crane 404
- Other Heating: Solar
Thanks Paul, you explained it well, understood. And yes , it has new sheet steel, very obvious from looking at the inside. The top ring is rusted beyond getting a shine back from the nickel, but the bottom 3 ring segments cleaned up well enough with light scotch guard. Probably just leave the rest the way it is, nice old patina.
- Sunny Boy
- Member
- Posts: 25729
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
alpineboard wrote: ↑Thu. Sep. 20, 2018 10:02 pmThanks Paul, you explained it well, understood. And yes , it has new sheet steel, very obvious from looking at the inside. The top ring is rusted beyond getting a shine back from the nickel, but the bottom 3 ring segments cleaned up well enough with light scotch guard. Probably just leave the rest the way it is, nice old patina.
A good coating of automotive paste wax on the nickel parts will reduce tendency to tarnish and help prevent further rusting.
Paul
-
- Member
- Posts: 8601
- Joined: Sat. May. 24, 2008 4:26 pm
- Location: Chester, NY
- Hot Air Coal Stoker Stove: LL AnthraKing 180K, Pocono110K,KStokr 90K, DVC
- Hand Fed Coal Stove: Invader 2
- Baseburners & Antiques: Wings Best, Glenwood #8(x2) Herald 116x
- Coal Size/Type: Rice,
- Other Heating: Heating Oil CH, Toyotomi OM 22
and so another member of the Taunton four horsemen clan is brought to life. After a 100 year rest, it is time to get to work. Well done, You will never regret this investment. Wings Best and Our Best, can anyone tell me the differences?
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
Nice find A
-
- Member
- Posts: 303
- Joined: Thu. Jan. 20, 2011 8:12 am
- Stoker Coal Boiler: Van Wert 600
- Hand Fed Coal Boiler: Tarm 202
- Hand Fed Coal Stove: Harman HXL, 150, Crane 88, Crane 404
- Other Heating: Solar
Yes, this one is an "Our Best", compared to "Wings Best"....? Will do some searching on Wiki.
Attachments
- Sunny Boy
- Member
- Posts: 25729
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Opps, sorry AB. I saw the 116X and the curved back pipe and thought it was a Wings Best.
Just noticed it has a Glenwood #6 bonnet and finial, too. Other than that and the name, it looks exactly like a Wings 116X.
Paul
Just noticed it has a Glenwood #6 bonnet and finial, too. Other than that and the name, it looks exactly like a Wings 116X.
Paul
-
- Member
- Posts: 303
- Joined: Thu. Jan. 20, 2011 8:12 am
- Stoker Coal Boiler: Van Wert 600
- Hand Fed Coal Boiler: Tarm 202
- Hand Fed Coal Stove: Harman HXL, 150, Crane 88, Crane 404
- Other Heating: Solar
Only you and some here would know that info to inform me, It all fits nicely. There is not much info on Leonard and Baker on the internet. I typed history of Leonard and Baker stove co. , not too many leads or links. L and B bought Glendale at some point in time. Will email the Barnstable co, and see if he has any history on stove manuf co's , dates, locations.
- Sunny Boy
- Member
- Posts: 25729
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
It's tough enough to find GW #6 and Wings 116X, you have the only example of an Our Best I can remember seeing.
Good thing Simon has his mustang now or he may be after it for his Taunton collection.
Paul
Good thing Simon has his mustang now or he may be after it for his Taunton collection.
Paul
- joeq
- Member
- Posts: 5743
- Joined: Sat. Feb. 11, 2012 11:53 am
- Location: Northern CT
- Hand Fed Coal Stove: G111, Southard Robertson
How many stove factories are there in Taunton? My G111 was sold under the false pretense it was a "Taunton" stove, when it had "Glenwood" cast in big letters on it. Are we to assume that LB, wings, and Glenwood are all the same manufacturer?
(By the way Alp, looks like you've got a Cadillac stove there. Deserving of some "new" nickel plating. Maybe Santa will be good to you this year.)
(By the way Alp, looks like you've got a Cadillac stove there. Deserving of some "new" nickel plating. Maybe Santa will be good to you this year.)
-
- Site Moderator
- Posts: 11417
- Joined: Wed. Nov. 05, 2008 5:11 pm
- Location: Kent CT
- Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
- Baseburners & Antiques: Glenwood Modern Oak 114
- Coal Size/Type: nut and pea
The only thing I would add to Paul's excellent tutorial is to measure the stove and base carefully to be sure you have it right way round. There might be slight difference.
- mntbugy
- Member
- Posts: 2046
- Joined: Fri. Dec. 23, 2016 2:36 pm
- Location: clearfield,pa
- Hand Fed Coal Stove: D S 1500, Warm Moring 400
- Baseburners & Antiques: Art Garland 145,GW114 ,Clarion 115, Vestal 20 Globe,New Royal22 Globe, Red Cross Oak 56,Acme Ventiduct 38,Radiant Airblast 626,Home Airblast 62,Moores #7,Moores 3way
- Coal Size/Type: stove and nut and some bit
- Other Heating: Propain
Paulie and I played with Skip's. Our,Wings and 6 . The load doors were very similar. But the GW 6 load door has a different radius to it. Not fitting on the Wings, or the Ours.
I think all 3 have slight differences in the finial.
The skirt pieces not sure about or grate frames.
I think all 3 have slight differences in the finial.
The skirt pieces not sure about or grate frames.