Clarion 115

Pauliewog · Post by **Pauliewog** » Thu. Nov. 02, 2017 4:57 pm

Looking good Artie ! Are you going to have the base recast or were you able to weld it up ? In the pic it looks like your going with a recast.

Paulie

mntbugy · Post by **mntbugy** » Thu. Nov. 02, 2017 5:50 pm

Was gas welded with nickel rod over a bed of burning kingsford .Still going to recast.

Pauliewog · Post by **Pauliewog** » Thu. Nov. 02, 2017 7:57 pm

mntbugy wrote: ↑
Thu. Nov. 02, 2017 5:50 pm
Was gas welded with nickel rod over a bed of burning kingsford .Still going to recast.

If you called me when you were heating it up ..... I would have brought over the hot dogs.

Paulie

mntbugy · Post by **mntbugy** » Sat. Dec. 23, 2017 7:26 pm

Just a dry test fit.

michaelanthony · Post by **michaelanthony** » Sat. Dec. 23, 2017 7:59 pm

This stove has been resurrected and is looking great! thanks for bringing it back to life. The little time I've had with my smaller BB, I'm hoping you have a large space for this heat machine.

Mike.

philthy · Post by **philthy** » Sat. Dec. 23, 2017 8:19 pm

Looking good! It's amazing how much time a person can get into one of these projects. It can be a lot of work when you think about it but i'm sure it don't feel that way to most.....

mntbugy · Post by **mntbugy** » Tue. Dec. 26, 2017 7:31 pm

Clean and green.

Need a new stink wheel to cut windows in barrel.

Hopefully I get my draw center slider recast back the end of this week.
Tomahawk forgot to recast it. Must have been a pack your lunch and smoke it day.

scalabro · Post by **scalabro** » Wed. Dec. 27, 2017 6:42 pm

Nice job!!!

What’s the diameter of the grate?

mntbugy · Post by **mntbugy** » Wed. Dec. 27, 2017 6:53 pm

scalabro wrote: ↑
Wed. Dec. 27, 2017 6:42 pm
Nice job!!!

What’s the diameter of the grate?

The pattern one is 13 inch, recast one is a good 12.875.

What is your base chamber height on your newer stove(PP). Mine is 10.750 inches high.

scalabro · Post by **scalabro** » Thu. Dec. 28, 2017 7:29 am

mntbugy wrote: ↑
Wed. Dec. 27, 2017 6:53 pm
The pattern one is 13 inch, recast one is a good 12.875.

What is your base chamber height on your newer stove(PP). Mine is 10.750 inches high.

6 & 1/2 high on the PP Stewart.

A Crawford 40 grate is 11& 1/4 wide...that’s a big Baseburner you have right there.

mntbugy · Post by **mntbugy** » Sun. Dec. 31, 2017 3:07 pm

More dry test fitting of barrel. Need to transfer fire pot holes for clinker face plate and and load door support plate.

Still waiting on slider recast. Going to find out Tuesday. It's holding everything up or it would have been done weeks ago.

Pauliewog · Post by **Pauliewog** » Sun. Dec. 31, 2017 4:23 pm

Looking good Artie !

There is a simple solution to that problem. You just have to pick up a half dozen other project stoves. That way you don't get frustrated, and always have something else to work on in situations like this.

On the downside ......... You might have to park the car outside.

Paulie

mntbugy · Post by **mntbugy** » Sun. Dec. 31, 2017 4:29 pm

They are done. Need to find more to buy. I'll be close to you on Wednesday
after another one. Dallas,PA

Pauliewog · Post by **Pauliewog** » Sun. Dec. 31, 2017 9:12 pm

Nice, give me a call when you are headed there. My new stove shop is in Dallas. I'll give you a hand loading it.

Paulie

mntbugy · Post by **mntbugy** » Sat. Jan. 06, 2018 6:27 pm

base is cemented along with fire pot.

Need to line fire pot with bricks, stove polish barrel, and install back pipe.
Hopefully a test burn in drive way this week.

Pics, just slapped together to see what it looks like.

Clarion 115

Attachments

Attachments

Attachments

Attachments