Just picked up a acme ventiduct 118, big old double heater, anyone have any parts for this or need any parts off of it?
Dana
Acme ventiduct
-
- New Member
- Posts: 14
- Joined: Sun. Nov. 27, 2016 12:35 pm
hello Dana,
Do you still have this stove and some of the parts. I'm interested in the lower, lager front door with the central vent. Mine is chipped at the top lip so won't seal properly, plus the hinges are worn and the door sags a touch. You still have that door?
Sincerely, Dan Rochester, Ny
Do you still have this stove and some of the parts. I'm interested in the lower, lager front door with the central vent. Mine is chipped at the top lip so won't seal properly, plus the hinges are worn and the door sags a touch. You still have that door?
Sincerely, Dan Rochester, Ny
-
- Member
- Posts: 771
- Joined: Sun. Jan. 18, 2015 9:40 pm
- Location: plainfield NH
- Hand Fed Coal Furnace: newmac wood,coal,oil como
- Baseburners & Antiques: 20th century laurel, glenwood hickory,crawford fairy
- Coal Size/Type: nut, stove
- Contact:
Yes, I will go out in the morning and take some pics of the pieces you need.
Dana
Dana
-
- Member
- Posts: 771
- Joined: Sun. Jan. 18, 2015 9:40 pm
- Location: plainfield NH
- Hand Fed Coal Furnace: newmac wood,coal,oil como
- Baseburners & Antiques: 20th century laurel, glenwood hickory,crawford fairy
- Coal Size/Type: nut, stove
- Contact:
Door is perfect has no hindge drop when opened, attached are pics
Dana
Dana
Attachments
-
- New Member
- Posts: 14
- Joined: Sun. Nov. 27, 2016 12:35 pm
It seems like it could be the same doors as mine. I would need the smaller top door too. I noticed mine is chipped along the bottom and doesn't seal well to the top of the lower door. My ACME stove has a "38" in the skirt just below the center of the bottom door. Does yours too? Sincerely, Dan
-
- Member
- Posts: 771
- Joined: Sun. Jan. 18, 2015 9:40 pm
- Location: plainfield NH
- Hand Fed Coal Furnace: newmac wood,coal,oil como
- Baseburners & Antiques: 20th century laurel, glenwood hickory,crawford fairy
- Coal Size/Type: nut, stove
- Contact:
I see no 38 but it has 118 cast into the skirt, the doors have 18-5 and 18-526 cast into them, I can get measurements if you need them the upper door handle is missing but the door is in good shape
-
- New Member
- Posts: 14
- Joined: Sun. Nov. 27, 2016 12:35 pm
Hmmm? Might not be the same parts/pieces after all. My stove doors have different casting numbers on them and I noticed that my vents look a bit different- not as domed as those shown on your stove. I opened the two doors together (top and bottom) and measured the inside dimensions of the rectangular opening. It is almost 12-1/2" wide by 15-3/4" tall at the narrowest places. Is your opening in the stove body the same size?
-
- Member
- Posts: 771
- Joined: Sun. Jan. 18, 2015 9:40 pm
- Location: plainfield NH
- Hand Fed Coal Furnace: newmac wood,coal,oil como
- Baseburners & Antiques: 20th century laurel, glenwood hickory,crawford fairy
- Coal Size/Type: nut, stove
- Contact:
Sorry it has taken so long for me to get back to you, I got busy and forgot all about it until I walk past it last night.
If you want to pay the shipping I will send you the doors and you can see if they fit, if they do give me $50 for them if they don’t send them back
If you want to pay the shipping I will send you the doors and you can see if they fit, if they do give me $50 for them if they don’t send them back