Art's Garland
- mntbugy
- Member
- Posts: 2042
- Joined: Fri. Dec. 23, 2016 2:36 pm
- Location: clearfield,pa
- Hand Fed Coal Stove: D S 1500, Warm Moring 400
- Baseburners & Antiques: Art Garland 145,GW114 ,Clarion 115, Vestal 20 Globe,New Royal22 Globe, Red Cross Oak 56,Acme Ventiduct 38,Radiant Airblast 626,Home Airblast 62,Moores #7,Moores 3way
- Coal Size/Type: stove and nut and some bit
- Other Heating: Propain
Gotta get a couple stove done before I lose free electric,compressed air, and natural gas, plus machine time.
I really like 3 phase power.
I really like 3 phase power.
- mntbugy
- Member
- Posts: 2042
- Joined: Fri. Dec. 23, 2016 2:36 pm
- Location: clearfield,pa
- Hand Fed Coal Stove: D S 1500, Warm Moring 400
- Baseburners & Antiques: Art Garland 145,GW114 ,Clarion 115, Vestal 20 Globe,New Royal22 Globe, Red Cross Oak 56,Acme Ventiduct 38,Radiant Airblast 626,Home Airblast 62,Moores #7,Moores 3way
- Coal Size/Type: stove and nut and some bit
- Other Heating: Propain
Starting to look better than a pile of parts.
Might be finished tomorrow?
Might be finished tomorrow?
Attachments
- mntbugy
- Member
- Posts: 2042
- Joined: Fri. Dec. 23, 2016 2:36 pm
- Location: clearfield,pa
- Hand Fed Coal Stove: D S 1500, Warm Moring 400
- Baseburners & Antiques: Art Garland 145,GW114 ,Clarion 115, Vestal 20 Globe,New Royal22 Globe, Red Cross Oak 56,Acme Ventiduct 38,Radiant Airblast 626,Home Airblast 62,Moores #7,Moores 3way
- Coal Size/Type: stove and nut and some bit
- Other Heating: Propain
Did some dry fit testing today. Poured a heaping bucket of nut in magazine.
It just filled the fire pot and about an
Inch and a half into magazine.
A few crumbs were laying on the back shelf of firepot. Not enough to get excited about??
Scratched the fresh paint in magazine,firepot and grates.
It just filled the fire pot and about an
Inch and a half into magazine.
A few crumbs were laying on the back shelf of firepot. Not enough to get excited about??
Scratched the fresh paint in magazine,firepot and grates.
Attachments
- mntbugy
- Member
- Posts: 2042
- Joined: Fri. Dec. 23, 2016 2:36 pm
- Location: clearfield,pa
- Hand Fed Coal Stove: D S 1500, Warm Moring 400
- Baseburners & Antiques: Art Garland 145,GW114 ,Clarion 115, Vestal 20 Globe,New Royal22 Globe, Red Cross Oak 56,Acme Ventiduct 38,Radiant Airblast 626,Home Airblast 62,Moores #7,Moores 3way
- Coal Size/Type: stove and nut and some bit
- Other Heating: Propain
Just needs nickel plated.
Ready for pick up Mr. Hmm, possibility,cheap.
Ready for pick up Mr. Hmm, possibility,cheap.
Attachments
- mntbugy
- Member
- Posts: 2042
- Joined: Fri. Dec. 23, 2016 2:36 pm
- Location: clearfield,pa
- Hand Fed Coal Stove: D S 1500, Warm Moring 400
- Baseburners & Antiques: Art Garland 145,GW114 ,Clarion 115, Vestal 20 Globe,New Royal22 Globe, Red Cross Oak 56,Acme Ventiduct 38,Radiant Airblast 626,Home Airblast 62,Moores #7,Moores 3way
- Coal Size/Type: stove and nut and some bit
- Other Heating: Propain
Garland still burning 12 hours on 15# of nut.
Some early numbers.
Bottom of clinker doors 415-445.
Top of load doors 236-250.
Fire pot 700-759.
Top of 48 inch smoke pipe 110 ish.
Draft very little.
Primary air open 3/8-7/16.
Base mode.
Not bad for the first run.
Some early numbers.
Bottom of clinker doors 415-445.
Top of load doors 236-250.
Fire pot 700-759.
Top of 48 inch smoke pipe 110 ish.
Draft very little.
Primary air open 3/8-7/16.
Base mode.
Not bad for the first run.
- Sunny Boy
- Member
- Posts: 25554
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Your right, not bad at all. in fact, with that 110 just 48 inches up the pipe, those are wonderful numbers. Wish my #6 could drop the temps that much by the time it gets to the pipe.
Congrats on resurrecting another Beauty, Artie.
Paul
Congrats on resurrecting another Beauty, Artie.
Paul