I had a thread in the anthracite. Figured I'd better move here since I plan on using bit if the local stuff will work.
Will 6" pipe squeeze over the oval? I don't see any provisions for a mechanical fastener? Is drilling a screw hole in the flange acceptable?
Should I use mpd or Baro? Planning on burning bit.
Also if anyone knows what size that acme screw in the bottom back side that controls the air is I need to get one.
Florence No. 77
-
- Member
- Posts: 1137
- Joined: Fri. Feb. 12, 2016 2:36 pm
- Hand Fed Coal Boiler: Harman SF360
- Hand Fed Coal Stove: T.O.M (Warm Morning converted to baseburner by Steve) Round Oak 1917 Door model O-3, Warm Morning 400, Warm Morning 524, Warm Morning 414,Florence No.77, Warm Morning 523-b
- Hand Fed Coal Furnace: Clayton 7.1/DS Machine basement stove/ Harman SF1500
- Baseburners & Antiques: Renown Parlor stove 87B
- Coal Size/Type: Bituminous/anthracite
- Other Heating: Harman Accentra, enviro omega, Vermont Ironworks Elm stove, Quadrafire Mt Vernon, Logwood stove, Sotz barrel stove,
-
- Member
- Posts: 1137
- Joined: Fri. Feb. 12, 2016 2:36 pm
- Hand Fed Coal Boiler: Harman SF360
- Hand Fed Coal Stove: T.O.M (Warm Morning converted to baseburner by Steve) Round Oak 1917 Door model O-3, Warm Morning 400, Warm Morning 524, Warm Morning 414,Florence No.77, Warm Morning 523-b
- Hand Fed Coal Furnace: Clayton 7.1/DS Machine basement stove/ Harman SF1500
- Baseburners & Antiques: Renown Parlor stove 87B
- Coal Size/Type: Bituminous/anthracite
- Other Heating: Harman Accentra, enviro omega, Vermont Ironworks Elm stove, Quadrafire Mt Vernon, Logwood stove, Sotz barrel stove,
I should be able to weld a t handle to an acme screw. I just wondered if anyone knew the thread pitch off hand. I don't have any acme thread pitch gauges. Hopefully it's not some oddball pitch. It looks like it was patented in 1899 so maybe if I'm lucky they used standard machining practices.
- freetown fred
- Member
- Posts: 30302
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
It's probably not--the stove was built before the genus's got hold of it!!!
-
- Member
- Posts: 1137
- Joined: Fri. Feb. 12, 2016 2:36 pm
- Hand Fed Coal Boiler: Harman SF360
- Hand Fed Coal Stove: T.O.M (Warm Morning converted to baseburner by Steve) Round Oak 1917 Door model O-3, Warm Morning 400, Warm Morning 524, Warm Morning 414,Florence No.77, Warm Morning 523-b
- Hand Fed Coal Furnace: Clayton 7.1/DS Machine basement stove/ Harman SF1500
- Baseburners & Antiques: Renown Parlor stove 87B
- Coal Size/Type: Bituminous/anthracite
- Other Heating: Harman Accentra, enviro omega, Vermont Ironworks Elm stove, Quadrafire Mt Vernon, Logwood stove, Sotz barrel stove,
How much rise is needed before making a 90* turn in the stove pipe? Since this is going in the basement there isn't much headroom.
-
- Site Moderator
- Posts: 11417
- Joined: Wed. Nov. 05, 2008 5:11 pm
- Location: Kent CT
- Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
- Baseburners & Antiques: Glenwood Modern Oak 114
- Coal Size/Type: nut and pea
Wrap a string around the oval exhaust and measure it. 6 inch pipe is close to 19 inches around, 18.85 inside..
You need enough rise to install the MPD if you want.
You need enough rise to install the MPD if you want.