Steam Verses Diesel
- DePippo79
- Member
- Posts: 734
- Joined: Tue. Mar. 05, 2013 3:17 pm
- Location: Hampton, NH
- Baseburners & Antiques: Glenwood Oak 40, Stanley Argand No. 30, Glenwood Modern Oak 114, Stanley Argand No. 20 missing parts.
- Coal Size/Type: Anthracite. Stove and nut size.
- Other Heating: Oil hot water.
Yup. Think it's time to sell some cars and buy myself a lathe. I want to build a steam engine. Cool video.
Matt
Matt
- just peter
- Member
- Posts: 222
- Joined: Sun. Nov. 20, 2011 3:22 pm
- Location: North Holland, The Netherlands.
- Hand Fed Coal Stove: Weso 225 C3, Susler Altan, Wasseralfingen 440, Susler Altan
- Coal Size/Type: bituminous coal,
It's mentioned before, coal is a adiction
- Duengeon master
- Member
- Posts: 1958
- Joined: Sun. May. 06, 2007 7:32 am
- Location: Penndel, Pa.
- Hand Fed Coal Stove: Harmon Mark III
- Coal Size/Type: Anthracite pea and nut mix. Bituminous lump
The steam tractor probably weighs three times more than the diesel one. Traction does the job.
- coaledsweat
- Site Moderator
- Posts: 13768
- Joined: Fri. Oct. 27, 2006 2:05 pm
- Location: Guilford, Connecticut
- Stoker Coal Boiler: Axeman Anderson 260M
- Coal Size/Type: Pea
Peak tourqe at zero RPM doesn't hurt either.
- Rob R.
- Site Moderator
- Posts: 18009
- Joined: Fri. Dec. 28, 2007 4:26 pm
- Location: Chazy, NY
- Stoker Coal Boiler: EFM 520
- Hand Fed Coal Stove: Chubby Jr
I agree, this is apples to oranges. A modern articulated tractor straight out of the field would drag that "hot rod" around.Duengeon master wrote:The steam tractor probably weighs three times more than the diesel one.
-
- Member
- Posts: 95
- Joined: Wed. Nov. 12, 2014 9:34 pm
- Location: LaFollette, TN
- Hand Fed Coal Furnace: Currently a Warm Morning 414 A. Previously had a Hot Blast 1321
- Coal Size/Type: To Be Determined
- Other Heating: propane
Looks like an aweful expensive way to plow. LOL.
That steamer probably weighs close to what that puller is used to pulling after its had a run on the sled. The sleds are light to start and get heavier the farther they go when they have momentum and speed and are into the power range.
That steamer probably weighs close to what that puller is used to pulling after its had a run on the sled. The sleds are light to start and get heavier the farther they go when they have momentum and speed and are into the power range.
- wsherrick
- Member
- Posts: 3744
- Joined: Wed. Jun. 18, 2008 6:04 am
- Location: High In The Poconos
- Hand Fed Coal Stove: Glenwood Base Heater, Crawford Base Heater
- Baseburners & Antiques: Crawford Base Heater, Glenwood, Stanley Argand
- Coal Size/Type: Chestnut, Stove Size
3,000 foot pounds of torque at 0 to 1 RPM, will cream the internal combustion engines hands down.
-
- Member
- Posts: 12236
- Joined: Thu. Mar. 13, 2008 10:29 am
- Location: Linesville, Pa.
- Hot Air Coal Stoker Furnace: keystoker 160
- Hand Fed Coal Stove: hitzer 75 in garage
Many years ago I got to run an old Case Sod Buster (I believe it was called) anyhow it was a lot larger that the one in the video & used in Kansas. If I recall correctly the real wheels were about 3 feet wide or better & had 3X5 2"thick steel cleats welded on for traction. It was said that a few wagons would go with it along with several teams of horses & a huge series of plows behind, they would start in the AM & plow until near dark then the teams turned the plow assembly around & the next morning start back. After a few days head start the planters would start following them up. Real low horse power but if it had the traction I think it could have climbed most anything. Not fast like the Stanleys & not fun like they were but it gave you a real respect for pure torque & what it could do.