Considering whether it makes sense to clean my chimney. My 28' ladder won't get me to the top of the chimney so I'll have to do everything from below. Whether through the clean-out or the thimble, there's about a 2' horizontal run to the main vertical run up. It looks like most of the chimney brush kits come with 3' x 3/8" fiberglass rods. I'm wondering whether any chimney rod can make this kind of turn up or do I need to go with a more flexible (and likely expensive) rod? Also, how do rod thickness and length factor in to flexibility?
Your thoughts please?
Chimney Rods
-
- Member
- Posts: 6515
- Joined: Sun. Feb. 10, 2008 3:48 pm
- Location: Cape Cod, MA
- Stoker Coal Boiler: want AA130
- Hand Fed Coal Stove: DS Machine BS#4, Harman MKII, Hitzer 503,...
- Coal Size/Type: Pea/Nut/Stove
The cleanout should be the better choice...
Less or no horizontal run...
You will never get the brush to make a 90* turn into the chimney...
A tape will not have the strength to do a push up the chimney...
Less or no horizontal run...
You will never get the brush to make a 90* turn into the chimney...
A tape will not have the strength to do a push up the chimney...
- keegs
- Member
- Posts: 678
- Joined: Sat. Dec. 24, 2016 7:38 pm
- Location: Bridgewater, ME
- Hand Fed Coal Stove: Chubby (main floor)
- Coal Size/Type: nut
There's no difference in horizontal run between the clean out and the thimble. The thimble is round though and the clean out is square.CapeCoaler wrote: ↑Thu. Dec. 21, 2017 7:36 pmThe cleanout should be the better choice...
Less or no horizontal run...
You will never get the brush to make a 90* turn into the chimney...
A tape will not have the strength to do a push up the chimney...
Rutland advertises a 6' x 1/4" rod that will do a 90. I think it's difficult in my situation. The flue is 6" x 6". That's a pretty tight turn.
There's a plumber's snake that's much stiffer than I'd imagine tape would be. I think it's a kind of wound steel that forms a flexible steel cable. Either way though, you'd have to attach a brush to the end of it. Not sure how you would do that.
-
- Site Moderator
- Posts: 11417
- Joined: Wed. Nov. 05, 2008 5:11 pm
- Location: Kent CT
- Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
- Baseburners & Antiques: Glenwood Modern Oak 114
- Coal Size/Type: nut and pea
Has a pipe thread just like the cleaning rods. You want the flat steel plumbers snake. About 1/2 inch wide.
-
- Member
- Posts: 6515
- Joined: Sun. Feb. 10, 2008 3:48 pm
- Location: Cape Cod, MA
- Stoker Coal Boiler: want AA130
- Hand Fed Coal Stove: DS Machine BS#4, Harman MKII, Hitzer 503,...
- Coal Size/Type: Pea/Nut/Stove
Ah yes that kind of snake...
Might do the trick...
Use them for clearing blockages in the septic pipes...
Might do the trick...
Use them for clearing blockages in the septic pipes...
-
- Member
- Posts: 28
- Joined: Fri. Dec. 14, 2018 11:04 pm
- Location: Union, Maine
- Hand Fed Coal Stove: Sun mogul 295 laundry stove
- Baseburners & Antiques: Crawford Treasure 12
- Coal Size/Type: Nut
sooteater on amazon. I bought two. You can replace the heads easy with weed eater trimmer string when they wear out. You cut them to size for your chimney. The flexible rods bend to almost 90 degrees. 2 kits gave me enough rod to clean my 32 foot chimney. Worked great for me, my boss and 3 friends. My chimney cleanout door is 6 inches or so above the cellar floor.
- keegs
- Member
- Posts: 678
- Joined: Sat. Dec. 24, 2016 7:38 pm
- Location: Bridgewater, ME
- Hand Fed Coal Stove: Chubby (main floor)
- Coal Size/Type: nut
Thanks oldschoolhouse, I picked up a brush and rod kit, used off CL. It had the fiberglass 3' rods. I bent the steel wire at the base of the brush and with some patience and persuasion I was able to make the turn and push the brush up through and out the top of the chimney. I watched some Youtube video on the Sooteater... looks like a home run.