Offset stove pipe?
-
- Member
- Posts: 4197
- Joined: Wed. Oct. 03, 2012 9:53 am
- Location: Western Massachusetts
- Baseburners & Antiques: Crawford 40, PP Stewart No. 14, Abendroth Bros "Record 40"
- Coal Size/Type: Stove / Anthracite.
- Other Heating: Oil fired, forced hot air.
Anybody have a source for this type (fabricated) offset pipe in the USA?
https://www.directflues.co.uk/index.php?page=shop.product_de ... t&Itemid=7
https://www.directflues.co.uk/index.php?page=shop.product_de ... t&Itemid=7
-
- Member
- Posts: 6515
- Joined: Sun. Feb. 10, 2008 3:48 pm
- Location: Cape Cod, MA
- Stoker Coal Boiler: want AA130
- Hand Fed Coal Stove: DS Machine BS#4, Harman MKII, Hitzer 503,...
- Coal Size/Type: Pea/Nut/Stove
Have not seen any...
ya just might have to fab this one up...
Most use the 45* elbows to do the job...
Most areas had or still have a stove installer with a metal shop...
Liability on a welded up part might preclude its manufacture in the states...
There is such a place on The Cape...
They are good...
but I never had them make such an offset...
Mostly straight pipe and adapters...
Muffler shop that does diesel exhausts might be able to bend one up...
Got to think outside the box on this one...
ya just might have to fab this one up...
Most use the 45* elbows to do the job...
Most areas had or still have a stove installer with a metal shop...
Liability on a welded up part might preclude its manufacture in the states...
There is such a place on The Cape...
They are good...
but I never had them make such an offset...
Mostly straight pipe and adapters...
Muffler shop that does diesel exhausts might be able to bend one up...
Got to think outside the box on this one...
- D-frost
- Member
- Posts: 1186
- Joined: Sun. Dec. 08, 2013 7:10 am
- Location: Southern New Hampshire
- Hand Fed Coal Stove: Harman MK ll
- Hand Fed Coal Furnace: Yukon Eagle I (multi-fuel oil, wood/coal)
- Baseburners & Antiques: Herald 'fireside oak'
- Coal Size/Type: nut/stove-Blaschak/Lehigh
Scott,
About 15 yrs. ago, when I stuffed a Morso woodstove into a fireplace at the Plum Is. cottage, these people made me a stainless adapter to go from square 12"x12" flue to 8" round. It's still there-planning to replace the Morso with a Chubby in the Spring.
Port Sheet Metal Inc.
154 State St.
Newburyport, Ma. 01950
978 462-6132
Cheers
About 15 yrs. ago, when I stuffed a Morso woodstove into a fireplace at the Plum Is. cottage, these people made me a stainless adapter to go from square 12"x12" flue to 8" round. It's still there-planning to replace the Morso with a Chubby in the Spring.
Port Sheet Metal Inc.
154 State St.
Newburyport, Ma. 01950
978 462-6132
Cheers
- coaledsweat
- Site Moderator
- Posts: 13766
- Joined: Fri. Oct. 27, 2006 2:05 pm
- Location: Guilford, Connecticut
- Stoker Coal Boiler: Axeman Anderson 260M
- Coal Size/Type: Pea
I would think any HVAC supply house could fab one up.
-
- Verified Business Rep.
- Posts: 356
- Joined: Mon. Aug. 03, 2009 10:11 am
- Location: southern anthracite field,Schuylkill County,Pa.
- Stoker Coal Boiler: EFM 520
- Hand Fed Coal Stove: warm morning # 500
- Baseburners & Antiques: Peninsular Western Hot Blast No.44K and Reading Foundry & Supply Co.
Can't you do that by using two adjustable elbows,adjusted accordingly at 45s?
-
- Member
- Posts: 4197
- Joined: Wed. Oct. 03, 2012 9:53 am
- Location: Western Massachusetts
- Baseburners & Antiques: Crawford 40, PP Stewart No. 14, Abendroth Bros "Record 40"
- Coal Size/Type: Stove / Anthracite.
- Other Heating: Oil fired, forced hot air.
Yes.fifthg wrote:Can't you do that by using two adjustable elbows,adjusted accordingly at 45s?
I would like a one piece section of 316L though...that's why I asked for a source.... hahahahahahahahaha
-
- Member
- Posts: 6515
- Joined: Sun. Feb. 10, 2008 3:48 pm
- Location: Cape Cod, MA
- Stoker Coal Boiler: want AA130
- Hand Fed Coal Stove: DS Machine BS#4, Harman MKII, Hitzer 503,...
- Coal Size/Type: Pea/Nut/Stove
Welding shop...
TIG...
TIG...
-
- Member
- Posts: 4197
- Joined: Wed. Oct. 03, 2012 9:53 am
- Location: Western Massachusetts
- Baseburners & Antiques: Crawford 40, PP Stewart No. 14, Abendroth Bros "Record 40"
- Coal Size/Type: Stove / Anthracite.
- Other Heating: Oil fired, forced hot air.
CapeCoaler wrote:Welding shop...
TIG...
No Kidding ?
All these are obvious...
A source for a part is what's easiest....hahahahahahahahaha
-
- Verified Business Rep.
- Posts: 356
- Joined: Mon. Aug. 03, 2009 10:11 am
- Location: southern anthracite field,Schuylkill County,Pa.
- Stoker Coal Boiler: EFM 520
- Hand Fed Coal Stove: warm morning # 500
- Baseburners & Antiques: Peninsular Western Hot Blast No.44K and Reading Foundry & Supply Co.
I found it!I will sell to YOU at a reasonable mark-up!
- D-frost
- Member
- Posts: 1186
- Joined: Sun. Dec. 08, 2013 7:10 am
- Location: Southern New Hampshire
- Hand Fed Coal Stove: Harman MK ll
- Hand Fed Coal Furnace: Yukon Eagle I (multi-fuel oil, wood/coal)
- Baseburners & Antiques: Herald 'fireside oak'
- Coal Size/Type: nut/stove-Blaschak/Lehigh
Scott,
Worse case: Buy the one from the Brits. I think the pound/dollar ratio is almost 1:1. Also, maybe you can get the adapter out of Canada, just sayin'.......
Worse case: Buy the one from the Brits. I think the pound/dollar ratio is almost 1:1. Also, maybe you can get the adapter out of Canada, just sayin'.......
-
- Member
- Posts: 4197
- Joined: Wed. Oct. 03, 2012 9:53 am
- Location: Western Massachusetts
- Baseburners & Antiques: Crawford 40, PP Stewart No. 14, Abendroth Bros "Record 40"
- Coal Size/Type: Stove / Anthracite.
- Other Heating: Oil fired, forced hot air.
Great minds think alike DF!D-frost wrote:Scott,
Worse case: Buy the one from the Brits. I think the pound/dollar ratio is almost 1:1. Also, maybe you can get the adapter out of Canada, just sayin'.......
$45 plus shipping... but that could be the deal breaker.
-
- Member
- Posts: 6515
- Joined: Sun. Feb. 10, 2008 3:48 pm
- Location: Cape Cod, MA
- Stoker Coal Boiler: want AA130
- Hand Fed Coal Stove: DS Machine BS#4, Harman MKII, Hitzer 503,...
- Coal Size/Type: Pea/Nut/Stove
it always the shipping...
possibly customs...
possibly customs...
-
- Member
- Posts: 30
- Joined: Wed. Oct. 04, 2017 5:47 pm
- Baseburners & Antiques: Antique Shipmate 134 Marine coal and wood
- Coal Size/Type: nut size
Get in touch with this guy, Dan, for custom stuff. It's all 304 stainless that he does and he'll do any size from 4" on up and he's affordable. We had him fabricate some things for our boat stove (6") and appreciate his lifetime guarantee. In the salty ocean environment, that's a benefit for us. https://schoonerchandlery.com/store/dans-rugged-pipe is his marketplace shop.