Chimney Liner
- windyhill4.2
- Member
- Posts: 6072
- Joined: Fri. Nov. 22, 2013 2:17 pm
- Location: Jonestown,Pa.17038
- Stoker Coal Boiler: 1960 EFM520 installed in truck box
- Hand Fed Coal Stove: Crane 404 with variable blower
- Coal Size/Type: 404-nut, 520 rice ,anthracite for both
davebyer ,Welcome to the forum. I am known to be dense at times,so forgive me for saying I don't quite get the meaning of your question,& I prefer not to post an answer that will make me look even stupider. Maybe you can clarify the question with a bit more detail.
- Lightning
- Site Moderator
- Posts: 14669
- Joined: Wed. Nov. 16, 2011 9:51 am
- Location: Olean, NY
- Stoker Coal Boiler: Modified AA 130
- Coal Size/Type: Pea Size - Anthracite
We need further description of such vent.davebyer wrote:there was a vent at the top of the chimney that is now shut shuid I open it
Pictures would be a big help.
- Lightning
- Site Moderator
- Posts: 14669
- Joined: Wed. Nov. 16, 2011 9:51 am
- Location: Olean, NY
- Stoker Coal Boiler: Modified AA 130
- Coal Size/Type: Pea Size - Anthracite
There shouldn't be any closeable vent at the top of the chimney.davebyer wrote:when steel liner was installed the vents were shut
Unless I still don't understand..
- Lightning
- Site Moderator
- Posts: 14669
- Joined: Wed. Nov. 16, 2011 9:51 am
- Location: Olean, NY
- Stoker Coal Boiler: Modified AA 130
- Coal Size/Type: Pea Size - Anthracite
The warm air between the liner and brick should just stay there. It will help keep the liner warm for better drafting. I've never seen any type of vent like that at the top of the chimney, Maybe another member could elaborate if there is suppose to be such a thing.davebyer wrote:the light gray on pic were the vent holes for the chimney
now the warm air between the liner and the brick goes where?
- michaelanthony
- Member
- Posts: 4550
- Joined: Sat. Nov. 22, 2008 10:42 pm
- Location: millinocket,me.
- Hand Fed Coal Stove: Vigilant 2310, gold marc box stove
- Hand Fed Coal Furnace: Gold Marc Independence
- Baseburners & Antiques: Home Sparkle 12
- Coal Size/Type: 'nut
- Other Heating: Fujitsu mini split, FHA oil furnace
Pardon me, but I don't think you could be more vague. Chimney's don't have "vents" they have a beginning and an end and sometimes a clean out.
I keep reading this thread over and over and my head hurts.
I keep reading this thread over and over and my head hurts.
- windyhill4.2
- Member
- Posts: 6072
- Joined: Fri. Nov. 22, 2013 2:17 pm
- Location: Jonestown,Pa.17038
- Stoker Coal Boiler: 1960 EFM520 installed in truck box
- Hand Fed Coal Stove: Crane 404 with variable blower
- Coal Size/Type: 404-nut, 520 rice ,anthracite for both
The lite gray that I am seeing is just new mortar to replace loose or fallen out mortar,that would not be venting holes. Looks like whoever installed the liner ,correctly repaired the top of the chimney. The only place that should vent from a chimney is right out the top of the liner,no where else.davebyer wrote:the light gray on pic were the vent holes for the chimney
now the warm air between the liner and the brick goes where?
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
If the chimney is working now & has been--don't touch anything-whatever it might be. This is a question you need to ask who-ever did the liner install & I don't even want to get into liners
- lsayre
- Member
- Posts: 21781
- Joined: Wed. Nov. 23, 2005 9:17 pm
- Location: Ohio
- Stoker Coal Boiler: AHS S130 Coal Gun
- Coal Size/Type: Lehigh Anthracite Pea
- Other Heating: Resistance Boiler (13.5 KW), ComfortMax 75
Is the picture showing us a simple chimney cap, or a combination draft inducer/chimney cap (the latter having an electric fan in it)?
- Freespirit
- Member
- Posts: 164
- Joined: Fri. Sep. 28, 2012 10:01 pm
- Location: Lancaster NH Coos County
- Hand Fed Coal Stove: Alaska Kodiak
- Coal Size/Type: Pea or Nut
Chimney update
PostBy: Freespirit On: Tue Dec 01, 2015 10:25 am
I had a guy come yesterday he is a general contractor he climbed up and looked at my chimney. He said that the liner that I have was put in in 2 sections that one section came off from the other. He is coming back to remove that one section and put in a pipe at the top and put a cap on it and mortar it he said my Stainless steel liner looks good. He is going to do the pointing where my mortar is missing he said over all my chimney is in excellent shape. He is also going to strap the pipe in the fire place to take the weight off the liner that will remain. It is up far enough to get a good draft. He said he will be back on Saturday to do this but in the mean time I can use my stove the way it is, nothing is blocked. God only knows how long that the liner has been sitting there apart. Funny them chimney sweeps that came before never mentioned that my liner was in 2 pieces unless it wasn't at that point. Maybe we did that when we put the new piping in.
User avatar
Freespirit
Member
Posts: 59
Joined: Fri Sep 28, 2012 10:01 pm
Location: Coos County
Coal Size/Type: Pea or Nut
Stove/Furnace Make: Alaska
Stove/Furnace Model: Kodiak
Top
Re: Chimney update
New postBy: SWPaDon On: Tue Dec 01, 2015 10:34 am
Glad to hear you made some headway, but this info would have been better placed in your previous thread. That way everyone can see the entire progression and outcome of the issue.
SWPaDon
Member
Posts: 2887
Joined: Sun Nov 24, 2013 1:05 pm
Location: Southwest Pa.
Hand Fed Coal Furnace: Clayton 1600M
Coal Size/Type: Bituminous
Other Heating: Oil furnace that hasn't been fired in 14 years
Top
Re: Chimney update
New postBy: michaelanthony On: Tue Dec 01, 2015 10:47 am
I think a reputable chimney sweep would have noticed it if he did the required work. Too bad contractor number 2 wasn't number 1 he sounds honest. One reason some folks don't trust chimney sweeps. I'm glad the chimney is usable and safe, keep number 2's phone number and loose the sweep's.
never yell through a screen...you'll strain your voice.
User avatar
michaelanthony
Member
Posts: 3445
Joined: Thu Oct 06, 2011 6:38 pm
Location: millinocket,me.
Hand Fed Coal Stove: Vigilant 2310, gold marc box stove, vogelzang pot belly coat rack
Baseburners & Antiques: Home Sparkle 12
Coal Size/Type: Tractor supply Kimmels 'nut
Other Heating: Very cold FHA oil furnace
Top
Re: Chimney update
New postBy: windyhill4.2 On: Tue Dec 01, 2015 11:02 am
Sounds like good news.... BUT,i am totally lost,......like picking up a book to read & starting at the last chapter This is exactly why I kept my thread going during the whole process,from the beginning thru firing it & even beyond. B4 becoming a member I had read lots of threads that just stopped in the middle & left me Congratulations on the
David **** Firewood is made to be used in fireplaces,fire viewing stoves and for recreational heating only , or if under 50 yrs. old go ahead and work your butt off !!!!
User avatar
windyhill4.2
Member
Posts: 3536
Joined: Fri Nov 22, 2013 3:17 pm
Location: Jonestown,Pa.17038
Stoker Coal Boiler: 1960 EFM520 installed in truck box
Hand Fed Coal Stove: Crane 404 with variable blower
Coal Size/Type: 404-nut, 520 rice ,anthracite for both
Top
PostBy: Freespirit On: Tue Dec 01, 2015 10:25 am
I had a guy come yesterday he is a general contractor he climbed up and looked at my chimney. He said that the liner that I have was put in in 2 sections that one section came off from the other. He is coming back to remove that one section and put in a pipe at the top and put a cap on it and mortar it he said my Stainless steel liner looks good. He is going to do the pointing where my mortar is missing he said over all my chimney is in excellent shape. He is also going to strap the pipe in the fire place to take the weight off the liner that will remain. It is up far enough to get a good draft. He said he will be back on Saturday to do this but in the mean time I can use my stove the way it is, nothing is blocked. God only knows how long that the liner has been sitting there apart. Funny them chimney sweeps that came before never mentioned that my liner was in 2 pieces unless it wasn't at that point. Maybe we did that when we put the new piping in.
User avatar
Freespirit
Member
Posts: 59
Joined: Fri Sep 28, 2012 10:01 pm
Location: Coos County
Coal Size/Type: Pea or Nut
Stove/Furnace Make: Alaska
Stove/Furnace Model: Kodiak
Top
Re: Chimney update
New postBy: SWPaDon On: Tue Dec 01, 2015 10:34 am
Glad to hear you made some headway, but this info would have been better placed in your previous thread. That way everyone can see the entire progression and outcome of the issue.
SWPaDon
Member
Posts: 2887
Joined: Sun Nov 24, 2013 1:05 pm
Location: Southwest Pa.
Hand Fed Coal Furnace: Clayton 1600M
Coal Size/Type: Bituminous
Other Heating: Oil furnace that hasn't been fired in 14 years
Top
Re: Chimney update
New postBy: michaelanthony On: Tue Dec 01, 2015 10:47 am
I think a reputable chimney sweep would have noticed it if he did the required work. Too bad contractor number 2 wasn't number 1 he sounds honest. One reason some folks don't trust chimney sweeps. I'm glad the chimney is usable and safe, keep number 2's phone number and loose the sweep's.
never yell through a screen...you'll strain your voice.
User avatar
michaelanthony
Member
Posts: 3445
Joined: Thu Oct 06, 2011 6:38 pm
Location: millinocket,me.
Hand Fed Coal Stove: Vigilant 2310, gold marc box stove, vogelzang pot belly coat rack
Baseburners & Antiques: Home Sparkle 12
Coal Size/Type: Tractor supply Kimmels 'nut
Other Heating: Very cold FHA oil furnace
Top
Re: Chimney update
New postBy: windyhill4.2 On: Tue Dec 01, 2015 11:02 am
Sounds like good news.... BUT,i am totally lost,......like picking up a book to read & starting at the last chapter This is exactly why I kept my thread going during the whole process,from the beginning thru firing it & even beyond. B4 becoming a member I had read lots of threads that just stopped in the middle & left me Congratulations on the
David **** Firewood is made to be used in fireplaces,fire viewing stoves and for recreational heating only , or if under 50 yrs. old go ahead and work your butt off !!!!
User avatar
windyhill4.2
Member
Posts: 3536
Joined: Fri Nov 22, 2013 3:17 pm
Location: Jonestown,Pa.17038
Stoker Coal Boiler: 1960 EFM520 installed in truck box
Hand Fed Coal Stove: Crane 404 with variable blower
Coal Size/Type: 404-nut, 520 rice ,anthracite for both
Top
- Freespirit
- Member
- Posts: 164
- Joined: Fri. Sep. 28, 2012 10:01 pm
- Location: Lancaster NH Coos County
- Hand Fed Coal Stove: Alaska Kodiak
- Coal Size/Type: Pea or Nut
I don't know who did the liner install this house was a foreclosure and I bought it.freetown fred wrote:If the chimney is working now & has been--don't touch anything-whatever it might be. This is a question you need to ask who-ever did the liner install & I don't even want to get into liners