Dust Collection

Post Reply
 
User avatar
Snotzalot
Member
Posts: 196
Joined: Fri. Nov. 21, 2014 10:27 pm
Location: Some where over the Rainbow, Pa.
Hand Fed Coal Stove: Old Mill
Coal Size/Type: Nut/Reading
Other Heating: Elec

Post by Snotzalot » Sat. Feb. 28, 2015 1:11 pm

I use a ONEIDA Dust Deputy in my furniture shop to collect sanding dust. It does an excellent job of depositing the fine dust into the 5 gallon bucket and not in the vacuum. This allows easier disposal and the fine dust never makes it to the filter and won't clog the filter. I have been using a Jet Air Purifier near the stove to catch the fine dust but it's not 100%, I still get a layer of dust on the floor.

Today I rigged up my dust deputy, vacuum and the air filter all in the same area. At first shake down and ash removal it seems to do an excellent job of dust pick up. So for the rest of the season I'll continue the experiment. If it is successful next season it will all be contained in a cabinet. The hoses in the photo have wood dust from the shop on them and not coal dust. I need to take the garden hose to them! LOL!

Stay tuned.
dust collector.jpg
.JPG | 114.1KB | dust collector.jpg

 
stokerstove
Member
Posts: 179
Joined: Wed. Jan. 25, 2006 4:05 pm
Location: NE PA
Hot Air Coal Stoker Stove: Alaska Kodiak Stokerstove 1

Post by stokerstove » Sun. Mar. 01, 2015 2:43 pm

Good idea with the Dust Deputy. I've been meaning to get one or make my own. For me this would come in the handiest when I clean the system at the end of the season. I have a Delta Air purifier but it is semi-permanently mounted to the basement ceiling. I do turn it on when I'm making a lot of dust, be it from woodworking or stove related.

 
User avatar
Snotzalot
Member
Posts: 196
Joined: Fri. Nov. 21, 2014 10:27 pm
Location: Some where over the Rainbow, Pa.
Hand Fed Coal Stove: Old Mill
Coal Size/Type: Nut/Reading
Other Heating: Elec

Post by Snotzalot » Sun. Mar. 01, 2015 4:31 pm

Did a good shake down and poker job this morning plus ash removal and this set up seems to be working as I had hoped. I picked up a new filter for the vacuum today since it had been used in the wood shop for some time.

 
User avatar
nepacoal
Member
Posts: 1696
Joined: Wed. Nov. 21, 2012 7:49 am
Location: Coal Country
Stoker Coal Boiler: Keystoker KAA-4 / "Kelly" and an EFM 520 at my in-laws
Hand Fed Coal Boiler: Harman SF-260 - retired
Coal Size/Type: Buck

Post by nepacoal » Sun. Mar. 01, 2015 4:43 pm

I've had this setup for two years now. I can clean out 7 or 8 tons worth of fly ash buildup and not see any dust in the vacuum bag. Before setting this up, I would have to change the filter and bag after can single clean out. I use it to cleanup ash and coal dust from around the boiler several times a week as well as connect it to my saw to collect sawdust. The dust on the outside is caused by static. It's been a good purchase.

Attachments

IMG_20150301_162737.jpg
.JPG | 122.8KB | IMG_20150301_162737.jpg


 
User avatar
WNY
Member
Posts: 6307
Joined: Mon. Nov. 14, 2005 8:40 am
Location: Cuba, NY
Hot Air Coal Stoker Stove: Keystoker 90K, Leisure Line Hyfire I
Coal Size/Type: Rice
Contact:

Post by WNY » Sun. Mar. 01, 2015 5:39 pm

I have the Rockler Dust Right Vacuum canister/separator with my shop vac, works very similar for the ash cleanup.

I also built a dust collector cyclone for my workshop that works good too for my sawdust.

Attachments

DSCF7457.jpg
.JPG | 77.6KB | DSCF7457.jpg

 
User avatar
Snotzalot
Member
Posts: 196
Joined: Fri. Nov. 21, 2014 10:27 pm
Location: Some where over the Rainbow, Pa.
Hand Fed Coal Stove: Old Mill
Coal Size/Type: Nut/Reading
Other Heating: Elec

Post by Snotzalot » Sun. Mar. 01, 2015 6:21 pm

WNY nice home built set up!

 
WNYRob
Member
Posts: 264
Joined: Thu. Apr. 14, 2011 12:13 pm
Location: Springville, NY
Hot Air Coal Stoker Stove: Keystoker Koker controlled with CoalTrol

Post by WNYRob » Sun. Mar. 01, 2015 6:28 pm

I have the dust deputy also, but I still get fine dust coming through to the vacuum. I always attributed it to the dust being too light to settle out in the deputy.

 
User avatar
nepacoal
Member
Posts: 1696
Joined: Wed. Nov. 21, 2012 7:49 am
Location: Coal Country
Stoker Coal Boiler: Keystoker KAA-4 / "Kelly" and an EFM 520 at my in-laws
Hand Fed Coal Boiler: Harman SF-260 - retired
Coal Size/Type: Buck

Post by nepacoal » Sun. Mar. 01, 2015 6:32 pm

WNYRob wrote:I have the dust deputy also, but I still get fine dust coming through to the vacuum. I always attributed it to the dust being too light to settle out in the deputy.
Rob, I think you probably have a small leak in your collection tank. That will cause small amounts of dust to get into the vacuum. It must be 100% airtight.


 
User avatar
Snotzalot
Member
Posts: 196
Joined: Fri. Nov. 21, 2014 10:27 pm
Location: Some where over the Rainbow, Pa.
Hand Fed Coal Stove: Old Mill
Coal Size/Type: Nut/Reading
Other Heating: Elec

Post by Snotzalot » Sun. Mar. 01, 2015 8:44 pm

I have used the Dust Deputy in my commercial furniture shop for years on the sanding bench. I would guestimate 99% of the fine sanding dust stays in the collection tank.

 
User avatar
Snotzalot
Member
Posts: 196
Joined: Fri. Nov. 21, 2014 10:27 pm
Location: Some where over the Rainbow, Pa.
Hand Fed Coal Stove: Old Mill
Coal Size/Type: Nut/Reading
Other Heating: Elec

Post by Snotzalot » Tue. Mar. 17, 2015 4:51 pm

My Dust Deputy is now back in my wood shop. A nice collection of dust in the collection pail and the vacuum filter was clean. Looks like next season is going to get it's own Dust Deputy and vacuum.

 
User avatar
Omtas
New Member
Posts: 1
Joined: Thu. Jan. 07, 2021 9:12 am
Location: Victoria Melbourne

Post by Omtas » Thu. Jan. 07, 2021 12:22 pm

Ohh nice, I am looking to buy a new dust collector, which would be a good option for a great price?

 
Hoytman
Member
Posts: 5997
Joined: Wed. Jan. 18, 2017 11:30 pm
Location: swOH near a little town where the homes are mobile and the cars aren’t
Hand Fed Coal Stove: Hitzer 354
Coal Size/Type: nut coal
Other Heating: electric, wood, oil

Post by Hoytman » Thu. Jan. 07, 2021 12:28 pm

We need some more detailed pictures of peoples set-ups from different angles.

 
User avatar
WNY
Member
Posts: 6307
Joined: Mon. Nov. 14, 2005 8:40 am
Location: Cuba, NY
Hot Air Coal Stoker Stove: Keystoker 90K, Leisure Line Hyfire I
Coal Size/Type: Rice
Contact:

Post by WNY » Thu. Jan. 07, 2021 5:10 pm

you can always get a inexpensive one from Harbor Freight and with a few mod's it can work much better. A cyclone separator or simliar drum keeps much of the stuff from the bags/filter. I upgraded to a dual bag I bought from my neighbor, and added a knockout canister, works great. using my orginal setup for my new CNC router. just need to hook it up.

Attachments

dust_collector_final.jpg
.JPG | 86.4KB | dust_collector_final.jpg

Post Reply

Return to “Coal Bins, Chimneys, CO Detectors & Thermostats”