Questions on My Setup

This forum is for common products and questions such as chimney installations, CO detectors, coal bin designs and a variety of other general topics that do not fit into the other forums.
Post Reply
Posts: 20
Joined: Sat. Jan. 05, 2008 4:35 pm

Post Tue. Jan. 22, 2008 1:38 pm

i have read this forum several times and i'm still a bit confused. I have a liesure line pioneer tv with a swg power vent. the baro damper is plumb and level and the weight is set on 3. the manometer reads .03 at low and .035 at high burn. the power vent is set at 40% on. full burn temp readings are as follows. 550 deg at stove front, 240 deg on stove pipe 1 ft from stove, 149 deg after b/d, and 140 deg inside power vent at exhaust. (all taken using a laser) I have tried numerous settings with the b/d and power vent speed but the current give me the hottest stove temp .
am I in the ball park with this setup? I am concerned about the baro damper being connected to an elbow on one side and directly to the power vent on the other and not getting correct readings. I have co detector and they havn't gone off.
one more question, how do you measure the draft over the fire?
thanks for a great forum and your input

Mt Top Pa
baro damper.JPG
front view.JPG
mano probe in pipe.JPG

User avatar
Verified Business Rep.
Posts: 1929
Joined: Mon. Oct. 02, 2006 8:59 am
Stoker Coal Boiler: Leisure Line WL110 Dual Fuel, natural gas
Hot Air Coal Stoker Stove: Leisure Line Lil' Heater (rental house)
Coal Size/Type: Rice and Buckwheat Anthracite
Location: Wilkes Barre, PA

Post Tue. Jan. 22, 2008 2:03 pm

Hi tozz, welcome to the forum.

Based on your picture of the baro location that is fine, although my preference would be to mount it at least 1' from the elbow or the 4" to 6" adapter. I would also say by the amount your baro is open you are wasting heat out the stack. I adjust mine to give me .03 to .04 with the baro shut. Just remember as soon as the flap on the baro is open you are causing room air to mix with the flue gases to achieve the correct draft. IMO, not only is that pulling hot room air out of the house, but it is also causing more heat to go up the chimney than needed.

On my stove I achieve 600* stove temps while the stack at the power vent entrance is only 84* , the power vent inside at the exhaust is 60* on a cold day like today (also using a laser). One thing you need to be aware of, if your laser is not adjustable for emissivity, there can be an error based on the surface you are reading. The black stove pipe Vs the galvanized need different emissivity settings (high on the black and med or low on the silver depending on reflectivity).

To answer your concern, I feel you are safe running it as you are, the draft measurement is in the right spot, so really doesn't matter where the baro is. You can calibrate the weight location for your current set up by moving the weight and adjusting the rheostat to get the baro to just open at your desired setting.

With respect to measuring static pressure (the draft in the stove) over the fire you need to access the combustion area. My Harman has a small plug in the front of the stove over the ash door, I remove the plug and insert the manometer probe there to get this data. In my Alaska stoves I had to drill a hole and tap it for a 1/8 pipe plug. You can ask Jerry at LL about your stove to see if it already has a location to check this, if not using the same method I did on the Alaskas will work. Just remember to put a dab of never seize on the pipe threads. :idea:

Enjoy the science project! :)
Leisure Line Stove Company

Posts: 20
Joined: Sat. Jan. 05, 2008 4:35 pm

Post Tue. Jan. 22, 2008 7:59 pm

thank you Mathaus for your speedy reply and wealth of information.
i stoked it up and used your setting and ended up with hotter stove temps than before, 580* at stove front, 275* on stove pipe 1 ft from stove, and 95* at start of power vent. the baro is only fluttering. this is a much better setup than I was using.
i was under the impression that by having the baro open most of the time it was in fact saving heat by drawing off room air instead of the hotter air from the stove.

thanks again


Post Reply

Return to “Coal Bins, Chimneys, CO Detectors & Thermostats”