Stainless or Regular Steel Stove Pipe?

 
User avatar
keegs
Member
Posts: 669
Joined: Sat. Dec. 24, 2016 7:38 pm
Location: Bridgewater, ME
Hand Fed Coal Stove: Chubby (main floor)
Coal Size/Type: nut

Post by keegs » Thu. Dec. 29, 2016 8:54 pm

grumpy wrote:I use Heat Fab heavy black pipe, I don't do anything to it in summer and its fine at eight years old. K check your PM.
Great idea grumpy using gasket rope for packing the gap between the seven inch pipe and eight inch thimble.

 
User avatar
oliver power
Member
Posts: 2866
Joined: Sun. Apr. 16, 2006 9:28 am
Location: Near Dansville, NY
Stoker Coal Boiler: KEYSTOKER Kaa-2
Hand Fed Coal Stove: Hitzer 50-93 & 30-95, Vigilant (pre-2310), D.S. 1600 Circulator, Hitzer 254

Post by oliver power » Thu. Dec. 29, 2016 9:44 pm

I've used both. Flip a coin. It really doesn't matter. :)

 
User avatar
McGiever
Member
Posts: 9867
Joined: Sun. May. 02, 2010 11:26 pm
Location: Junction of PA-OH-WV
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hand Fed Coal Boiler: BUCKET A DAY water heater
Hand Fed Coal Stove: Warm Morning 414A
Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
Other Heating: Ground Source Heat Pump and some Solar

Post by McGiever » Mon. Jan. 02, 2017 9:58 am

SS or NOT has no final answer...no two installs are the same.
Works great for some and not so great for others...too many variables so "depends", is the only answer. ;)


 
rodhotter
Member
Posts: 29
Joined: Mon. Jan. 21, 2019 10:44 pm
Hand Fed Coal Stove: Harmaan MK I
Coal Size/Type: anthracite nut
Other Heating: oil

Post by rodhotter » Fri. Apr. 22, 2022 9:31 am

very old i see but i looked before + found NOTHING that lasts for ME. dont know what grade stainless i had but it does well in my garage pot belly i burn wood BUT NOT in my basement kitchen where the Harman MK I is. last pipes were the HeatFab black that were a bit spendy, felt heavy BUT they will be SHOT after this year with small holes in them + had some surface rust on seasons start. i brush the inside + used corrosion X in + out when new + outside when stored in my attic ASAP when stove gets shut down. basement kitchens are generally damp BUT not when the Harman is ON!!

 
User avatar
McGiever
Member
Posts: 9867
Joined: Sun. May. 02, 2010 11:26 pm
Location: Junction of PA-OH-WV
Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
Hand Fed Coal Boiler: BUCKET A DAY water heater
Hand Fed Coal Stove: Warm Morning 414A
Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
Other Heating: Ground Source Heat Pump and some Solar

Post by McGiever » Fri. Apr. 22, 2022 10:03 am

Wood= creosote good coating against corrosion.

Flyash = moisture seeking coating plus highly corrosive.

Adding exposer time really makes this bad.

Remove moisture is good, remove flyash coating good…remove moisture and flyash is great!!
And NO stove pipe metal type is immune to all flyash corrosion.

 
User avatar
2001Sierra
Member
Posts: 2210
Joined: Wed. May. 20, 2009 8:09 am
Location: Wynantskill NY, 10 miles from Albany
Hot Air Coal Stoker Stove: Keystoker 90 Chimney vent
Coal Size/Type: Rice
Other Heating: Buderus Oil Boiler 3115-34

Post by 2001Sierra » Fri. Apr. 22, 2022 10:59 am

rodhotter wrote:
Fri. Apr. 22, 2022 9:31 am
very old i see but i looked before + found NOTHING that lasts for ME. dont know what grade stainless i had but it does well in my garage pot belly i burn wood BUT NOT in my basement kitchen where the Harman MK I is. last pipes were the HeatFab black that were a bit spendy, felt heavy BUT they will be SHOT after this year with small holes in them + had some surface rust on seasons start. i brush the inside + used corrosion X in + out when new + outside when stored in my attic ASAP when stove gets shut down. basement kitchens are generally damp BUT not when the Harman is ON!!
I agree, I have used stainless, and now use 22Ga Black pipe. Both need thorough spring clean, rinse, dry with compressed air and my go to is fluid film and attic is nice dry storage.


 
User avatar
franpipeman
Member
Posts: 580
Joined: Fri. Jan. 11, 2008 4:27 pm
Location: Wernersville pa
Stoker Coal Boiler: efm 520 stoker fitzgibbons pressure vessel
Hand Fed Coal Stove: harman, russo
Coal Size/Type: rice
Other Heating: alpine propane condensing boiler radiant floor

Post by franpipeman » Wed. Apr. 27, 2022 1:30 pm

rockford chimney 316 Ti stainless

 
rodhotter
Member
Posts: 29
Joined: Mon. Jan. 21, 2019 10:44 pm
Hand Fed Coal Stove: Harmaan MK I
Coal Size/Type: anthracite nut
Other Heating: oil

Post by rodhotter » Mon. May. 02, 2022 9:10 pm

as i posted in another thread NOTHING lasts past 3 years + that was the costlier Heat Fab PITA to cut + install black pipe. i remove + brush it clean yearly before it rests in my attic. used various "protectants" but not fluid film + pipes pit outside + prolly inside as well. whatever thin stainless i got from venting pipes only went 2 years wondering if the cheap EZE to DIY install galvavized will be the best value this year with bloated pricing everywhere!! i have a Harman MK I on Pa anthracite + stove sets in my basement-kitchen + keeps me comfy on the cheep until it gets too warm + i shut it down to run my oil furnace on the same chimney.

 
User avatar
freetown fred
Member
Posts: 29218
Joined: Thu. Dec. 31, 2009 12:33 pm
Location: Freetown,NY 13803
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut

Post by freetown fred » Tue. May. 03, 2022 8:27 am

You talkin inside or outside pipe????????????????????????? I tend to change inside black pipe every 3 or 4 yrs anyway--from the attic up is triple wall.

Post Reply

Return to “Coal Bins, Chimneys, CO Detectors & Thermostats”