Keystoker Gear Motor. Anywhere to Get One?
-
- Member
- Posts: 60
- Joined: Fri. Nov. 23, 2007 5:23 pm
- Location: lebanon pa
- Coal Size/Type: rice
got an alaska gear motor thinking itd work in replacing part because of loud bearing noise and come to find out the top peg has a gear or spiral cut in it and the alaska skeleton motor does not. keystoker wants $112 and $15 to ship. anyone have one or know where to get one?
- McGiever
- Member
- Posts: 10130
- Joined: Sun. May. 02, 2010 11:26 pm
- Location: Junction of PA-OH-WV
- Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
- Hand Fed Coal Boiler: BUCKET A DAY water heater
- Hand Fed Coal Stove: Warm Morning 414A
- Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
- Other Heating: Ground Source Heat Pump and some Solar
Need more info.
What model KeYstoker Stove?
How many rpm's is gear motor?
How about a picture of gear motor?
What model KeYstoker Stove?
How many rpm's is gear motor?
How about a picture of gear motor?
- whistlenut
- Member
- Posts: 3548
- Joined: Sat. Mar. 17, 2007 6:29 pm
- Location: Central NH, Concord area
- Stoker Coal Boiler: AA130's,260's, AHS130&260's,EFM900,GJ & V-Wert
- Hand Fed Coal Boiler: Franks,Itasca 415,Jensen, NYer 130,Van Wert
- Hot Air Coal Stoker Furnace: Alaska, EFM, Keystoker, Yellow Flame
- Hot Air Coal Stoker Stove: Alaska, Keystoker-2,Leisure Line
- Hand Fed Coal Stove: Alaska, Gibraltar, Keystone,Vc Vigilant 2
- Hand Fed Coal Furnace: Ford, Jensen, NYer, Van Wert,
- Baseburners & Antiques: Glenwoods
- Coal Size/Type: Barley, Buck, Rice ,Nut, Stove
- Other Heating: Oil HWBB
There is more to picking the motor up somewhere else.....shaft diameter, shaft length, flat spot on shaft, rpm from the gear reduction....probably 2 rpm. Grainger Supply has them also, just make damned sure you have the same creature.
Do a search on Grainger.com for your intended replacement. ALSO, check the frame mounting holes, some are not compatible. If you cannot get satisfaction, please call the fine folks at Keystoker and it will be shipped same day..... I have not seen them at Tractor Supply, however many pellet stoves use the same motors....just remember to check the shaft size and diameter,
Do a search on Grainger.com for your intended replacement. ALSO, check the frame mounting holes, some are not compatible. If you cannot get satisfaction, please call the fine folks at Keystoker and it will be shipped same day..... I have not seen them at Tractor Supply, however many pellet stoves use the same motors....just remember to check the shaft size and diameter,
multiproducts.com racine wi.
- whistlenut
- Member
- Posts: 3548
- Joined: Sat. Mar. 17, 2007 6:29 pm
- Location: Central NH, Concord area
- Stoker Coal Boiler: AA130's,260's, AHS130&260's,EFM900,GJ & V-Wert
- Hand Fed Coal Boiler: Franks,Itasca 415,Jensen, NYer 130,Van Wert
- Hot Air Coal Stoker Furnace: Alaska, EFM, Keystoker, Yellow Flame
- Hot Air Coal Stoker Stove: Alaska, Keystoker-2,Leisure Line
- Hand Fed Coal Stove: Alaska, Gibraltar, Keystone,Vc Vigilant 2
- Hand Fed Coal Furnace: Ford, Jensen, NYer, Van Wert,
- Baseburners & Antiques: Glenwoods
- Coal Size/Type: Barley, Buck, Rice ,Nut, Stove
- Other Heating: Oil HWBB
Weren't you reading any of the posts you received to help eliminate this problem? Been there, done that. Just trying to help you NOT to do the same thing. I hope you have resolved the situation by no
Jim's suggestion will solve you problem afford ably, as will Graingers. LOOK AT ROTATION< GEAR REDUCTION AND SHAFT DIAMETER...please
Jim's suggestion will solve you problem afford ably, as will Graingers. LOOK AT ROTATION< GEAR REDUCTION AND SHAFT DIAMETER...please