Stove Black, What Is It?
Hi Guys,
Making some changes on my Harman SF 160, and want to paint the 16 gauge steel plates that i'm fabricating. What is stove black and where would you get it? Or what kind of paint would you use to make these parts the same color as the stove (black)? The parts will be added to the ash door, so not subject to the high heat.
JB
Making some changes on my Harman SF 160, and want to paint the 16 gauge steel plates that i'm fabricating. What is stove black and where would you get it? Or what kind of paint would you use to make these parts the same color as the stove (black)? The parts will be added to the ash door, so not subject to the high heat.
JB
-
- Member
- Posts: 312
- Joined: Wed. Dec. 26, 2007 10:06 pm
- Location: Glens Falls NY Area
- Hand Fed Coal Stove: Older Ashley Cabinet ( pre US Stove gobble up)
- Hand Fed Coal Furnace: Energy King 480 EK
- Coal Size/Type: Warm weather smaller coal. Cold weather larger coal.
- Other Heating: Oil Furnace Backup when repairs are needed
Hi Folks
Check in a hardware store for Rutland Fire Clay Products. Small Red and White Checkers on lable.
Used to use stuff called Coughlin's Stove Black but I cant seem to find it any more.
I agree with previous post about hi temp paint for steel especially new . It seems like once the steel has heated and cooled a few times and gets a tad of rust film the paint seems to adhere better.
Anyone know if Coughlins is still in business? They used to have a chimney cleaner in a yellow cardboard tube type box.
I was told that "stove black" is a wax base . I know it stinks when it gets hot first time so be prepared.
Check in a hardware store for Rutland Fire Clay Products. Small Red and White Checkers on lable.
Used to use stuff called Coughlin's Stove Black but I cant seem to find it any more.
I agree with previous post about hi temp paint for steel especially new . It seems like once the steel has heated and cooled a few times and gets a tad of rust film the paint seems to adhere better.
Anyone know if Coughlins is still in business? They used to have a chimney cleaner in a yellow cardboard tube type box.
I was told that "stove black" is a wax base . I know it stinks when it gets hot first time so be prepared.
- LsFarm
- Member
- Posts: 7383
- Joined: Sun. Nov. 20, 2005 8:02 pm
- Location: Michigan
- Stoker Coal Boiler: Axeman Anderson 260
- Hand Fed Coal Boiler: Self-built 'Big Bertha' SS Boiler
- Baseburners & Antiques: Keystone 11, Art Garland
As stated above, stove black is for porous surfaces like cast iron, Use a good high temp paint on new steel surfaces, it looks and works best..
Clean the new steel surfaces with solvent first,, steel usually has some oil on it when new.
Greg L.
Clean the new steel surfaces with solvent first,, steel usually has some oil on it when new.
Greg L.
Thanks Guys, for the info. I bought hi temp flat black spray paint and sanded the steel parts with 150 grit sandpaper. sanded it mostly to give the paint something to hang on to and also to clean it. Started to wonder if I should use a metal primer as it's being treated like anyother peace of metal. I've had good luck using Rustoleum red lead primer, which helps to prevent rust. Would you guys recommend using a primer before the top coat? These parts are only going to be on the ash door so they aren't going to get very hot anyway.
Thanks,
JB
Thanks,
JB
Here's a trick I used when I re-did the exhaust on my Harley. I took the pipes and gave them a good acid bath to etch the chrome. Then gave them a good coat of high temp primer, put the pipes in the oven at 400 for an hr. Next day did the same thing. 3rd day it was time to put the black on them, high temp gloss black. Same scenario. By day 5 I had a set of pipes that looked like they had black chrome on them. Never had a peeling, flaking or chalking problem and those pipes were still on the bike when I sold it. They had probably 50,000 miles on them too.
Deacon3j,
Now that is a cool idea!!! I don't think I want to get that fancy with the project i'm doing right now, but i'm going to copy your post for future reference. Thanks. BTW does your wife let you use her oven for projects like that or do you have your own oven
JB
Now that is a cool idea!!! I don't think I want to get that fancy with the project i'm doing right now, but i'm going to copy your post for future reference. Thanks. BTW does your wife let you use her oven for projects like that or do you have your own oven
JB
JB, it's easy but you have to do it right. The wife was a bit skeptical at first. lol! First thing to do is make sure the paint is completely dry before putting the parts in the oven. Put them in a cold oven and let them come up to temp along with the oven and you'll have almost no smell at all. The same applies for cooling, let all cool down together. Make sure your hands are clean before handling them or better yet, have something to grab them with. You'll have no fingerprints and a coating that's hard as iron when you're done.
This is real important when using the wife's oven. I baked a set of brake drums ONCE. Paint was still tacky. The house stunk for a while and it added a new dimension to my wife's cooking.it's easy but you have to do it right. The wife was a bit skeptical at first. lol! First thing to do is make sure the paint is completely dry before putting the parts in the oven.