Door Handle Broke!
-
- Member
- Posts: 260
- Joined: Mon. Nov. 17, 2008 8:28 pm
- Location: Hudson Valley, NY
In an attempt to adjust my door handle, the bolt snapped!
It looks like the original handle.
Is there a way to put a new bolt in? or do I need an entire new handle assembly? Anyone know if they are generic or do I need to buy one specifically for the Gibraltar?
It looks like the original handle.
Is there a way to put a new bolt in? or do I need an entire new handle assembly? Anyone know if they are generic or do I need to buy one specifically for the Gibraltar?
-
- Member
- Posts: 260
- Joined: Mon. Nov. 17, 2008 8:28 pm
- Location: Hudson Valley, NY
If I have someone re-weld a new stud to the end where it sticks through the door, would that hold up under the heat of the stove?
-
- Member
- Posts: 260
- Joined: Mon. Nov. 17, 2008 8:28 pm
- Location: Hudson Valley, NY
Anyone??? is this something I can just pickup at a hardware store? or will I need to fix it?
- Dallas
- Member
- Posts: 746
- Joined: Mon. Nov. 12, 2007 12:14 pm
- Location: NE-PA
- Hand Fed Coal Stove: Modified Russo C-35
- Other Heating: Oil Hot Air
I don't know how they are built, but if "somebody" put the thing in there, somebody else should be able to do the same thing. Put a picture up. Does the bolt screw out of the casting? I'm sure it wasn't cast with a bolt thread sticking out.
-
- Member
- Posts: 260
- Joined: Mon. Nov. 17, 2008 8:28 pm
- Location: Hudson Valley, NY
the handle sticks trough the door and has about 4" of thread that the two nuts lock a piece of metal to. I took it off so now there is no handle. just a hole
- Dallas
- Member
- Posts: 746
- Joined: Mon. Nov. 12, 2007 12:14 pm
- Location: NE-PA
- Hand Fed Coal Stove: Modified Russo C-35
- Other Heating: Oil Hot Air
As I said, my guess is, that the 4" threaded rod, was threaded steel, screwed into a cast iron handle. You'll have to inspect it carefully and see if it seems separate and will it screw out of the handle?
-
- Member
- Posts: 260
- Joined: Mon. Nov. 17, 2008 8:28 pm
- Location: Hudson Valley, NY
The handle is all one piece. It is threaded on the end.
-
- Member
- Posts: 260
- Joined: Mon. Nov. 17, 2008 8:28 pm
- Location: Hudson Valley, NY
Here it is.
Attachments
You should have no problem having a welding shop weld a new piece of threaded rod on there and grind it down flush to fit through the door and grind the flat to accommodate the D in the flat bar. They should cut it shorter first so you will have enough threads to work with for adjusting the handle. Get a new piece of threaded rod, nuts, and lock washers from Home Depot or a hardware store and bring it to a welding shop. That's a relatively small job.
Last edited by ScottD on Sun. Nov. 30, 2008 7:46 pm, edited 2 times in total.
-
- Member
- Posts: 260
- Joined: Mon. Nov. 17, 2008 8:28 pm
- Location: Hudson Valley, NY
Thanks. Does the hardware need to be any kind of special metal to resist the heat?
Not really but if you go with the bolt method like Dallas suggested, you could get a hardened one if you feel better about it.
Think about how much heat your stove will produce compared to the heat of the welder.
You won't have a problem.
Think about how much heat your stove will produce compared to the heat of the welder.
You won't have a problem.