Success!

Post Reply
 
Dann757
Member
Posts: 3363
Joined: Sat. Sep. 06, 2008 9:10 am

Post by Dann757 » Sat. Nov. 29, 2008 6:46 pm

I just got back from Upstate Rural New York, and a great Thanksgiving with lots of family I don't see very often. I walked in here after 3 hours on the road, and built a wood fire in my stove, with fallen sticks, and started putting in anthracite coal. I couldn't wait to totally complete my setup, baro never arrived from an Ebay win, so I have temporarily run the stack without one.

I have an anthracite fire going in my stove!!!!!! I was worried about getting it started, it started fine, although I might have let the fire burn down a little longer; the coal caught but there were still some 3" sticks burning in there. They kind of went to charcoal and are slowly being consumed as I write. Stack thermometer is slowly reading in the burn zone, it's around 300* now. I'm keeping an eye on it and learning!

I was afraid I would roast myself out of the building, but I think I can run and regulate the fire enough to get it where I want it! Just before December!

Absolute thanks to all the guys who have been so helpful!

Attachments

Picture 063.jpg
.JPG | 416.1KB | Picture 063.jpg

 
User avatar
Freddy
Member
Posts: 7293
Joined: Fri. Apr. 11, 2008 2:54 pm
Location: Orrington, Maine
Stoker Coal Boiler: Axeman Anderson 130 (pea)
Coal Size/Type: Pea size, Superior, deep mined

Post by Freddy » Sat. Nov. 29, 2008 9:58 pm

Woooohooooo! It'll take a while to get the hang of how it all works but it'll be worth it. Then it'll seem so easy.

 
lincolnmania
Member
Posts: 2684
Joined: Fri. Jan. 26, 2007 9:55 pm
Location: Birdsboro PA.
Stoker Coal Boiler: EFM 350
Hot Air Coal Stoker Furnace: reading allegheny stoker
Hot Air Coal Stoker Stove: alaska kodiak stoker 1986. 1987 triburner, 1987 crane diamond
Coal Size/Type: rice

Post by lincolnmania » Sat. Nov. 29, 2008 10:10 pm

nice! heat! :D


 
User avatar
Scottscoaled
Member
Posts: 2812
Joined: Tue. Jan. 08, 2008 9:51 pm
Location: Malta N.Y.
Stoker Coal Boiler: EFM 520, 700, Van Wert 800 GJ 61,53
Baseburners & Antiques: Magic Stewart 16, times 2!
Coal Size/Type: Lots of buck
Other Heating: Slant Fin electric boiler backup

Post by Scottscoaled » Sat. Nov. 29, 2008 10:27 pm

Hey!!! Nice looking stove. Does that have a combustion blower? What are those vents on the side? Post some more pictures if you have them. :) Scott

 
Dann757
Member
Posts: 3363
Joined: Sat. Sep. 06, 2008 9:10 am

Post by Dann757 » Sat. Nov. 29, 2008 10:42 pm

There's an opening on the back for a fan. I'm sure there's a squirrel cage fasco fan that will directly fit the opening. It's really a 17" barrel in a 24" x 24" box. I don't know what cfm I should get. I want a quiet fan. Expanded steel mesh is open to the inside. There's a long narrow opening at the back bottom too 10" x 2".

Attachments

Picture 012.jpg
.JPG | 496.2KB | Picture 012.jpg

 
User avatar
Freddy
Member
Posts: 7293
Joined: Fri. Apr. 11, 2008 2:54 pm
Location: Orrington, Maine
Stoker Coal Boiler: Axeman Anderson 130 (pea)
Coal Size/Type: Pea size, Superior, deep mined

Post by Freddy » Sun. Nov. 30, 2008 5:32 am

Here's a fan that might be what you're looking for?

http://www.grainger.com/Grainger/items/1TDP2


 
User avatar
JB Sparks
Member
Posts: 842
Joined: Sun. Oct. 19, 2008 8:09 pm
Location: north central Mass.

Post by JB Sparks » Sun. Nov. 30, 2008 6:31 am

Hi Freddy,
Your apsolutely right! I'm just now rounding the corner from learning how to run the coal boiler to, boy!this is pretty easy! :D

I bought the 1TDN5 blower from Grainger for my SF160. Works pretty well, although I only use it manually now to just liven up the fire for reload as I have learned how to run the stove as Mr. Harman intended, and it doesn't need the blower in normal operation.

What a great help all you guys have been on this forum, so much great information here :)

JB

 
Dann757
Member
Posts: 3363
Joined: Sat. Sep. 06, 2008 9:10 am

Post by Dann757 » Sun. Nov. 30, 2008 10:52 am

Freddy that's the style. My opening in the back of the stove is 3" square and there are tapped 10-32 mounting flange holes in a 4" x 1-1/2" distance. I'm wondering what kind of CFM is good. My friends' Gold Marc insert has a similar fan (which I kindly restored for them) that has a nice variable speed switch on it.
Last year I had a round bathroom fan mounted on an empty paint can reduced to 3" flexible duct to push air through the unit, it sat on the floor, very Rube Goldberg.

Post Reply

Return to “Hand Fired Coal Stoves & Furnaces Using Anthracite”