I just bought a house with a warm morning 400A. Last owner of house never used it but did have the chimney cleaned.
Never used a fire like this.
What recommendations do you have for me to check it is usable and then to start using it.
Also it’s in the daylight basement. Will it heat the upper levels of the house.
Final question. A lot of wood was left at the house . Should I burn this, anthracite or bituminous?
Using a warm morning 400A
-
- Member
- Posts: 6077
- Joined: Wed. Jan. 18, 2017 11:30 pm
- Location: swOH near a little town where the homes are mobile and the cars aren’t
- Hand Fed Coal Stove: Hitzer 354
- Coal Size/Type: nut coal
- Other Heating: electric, wood, oil
Are you familiar at all with burning any of those fuels? Not just burning them a couple of times, but really familiar with using any type of stove?
Having a chimney cleaned is not the same as making sure a chimney is safe.
A dark room and a flashlight will go a long way in checking a stove for leaky holes.
The WM can burn anything, but anthracite coal will be the cleanest burning with no chance of a chimney fire in an already clean and safe chimney. Anthracite has no foul smell like bituminous coal an no creosote like wood, or soot to worry about or to clean like bituminous coal. Anthracite is the shizzle you might say...it’s great.
That information is a good place to start. Be patient and others will likely be along here to help you after Christmas.
Having a chimney cleaned is not the same as making sure a chimney is safe.
A dark room and a flashlight will go a long way in checking a stove for leaky holes.
The WM can burn anything, but anthracite coal will be the cleanest burning with no chance of a chimney fire in an already clean and safe chimney. Anthracite has no foul smell like bituminous coal an no creosote like wood, or soot to worry about or to clean like bituminous coal. Anthracite is the shizzle you might say...it’s great.
That information is a good place to start. Be patient and others will likely be along here to help you after Christmas.
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
G, yes----anthracite if available would be your best/cleanest bet. Welcome to the FORUM my friend. Just remember, the only stupid questions are the ones we don't ask!!
-
- Member
- Posts: 2706
- Joined: Fri. Jan. 26, 2007 9:55 pm
- Location: Birdsboro PA.
- Stoker Coal Boiler: EFM 350
- Hot Air Coal Stoker Furnace: reading allegheny stoker
- Hot Air Coal Stoker Stove: alaska kodiak stoker 1986. 1987 triburner, 1987 crane diamond
- Coal Size/Type: rice
used to have one in my garage for extra heat near the garage door.
make sure there are no cracks in the stove. are the fire bricks intact?
make sure there are no cracks in the stove. are the fire bricks intact?
- McGiever
- Member
- Posts: 10130
- Joined: Sun. May. 02, 2010 11:26 pm
- Location: Junction of PA-OH-WV
- Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
- Hand Fed Coal Boiler: BUCKET A DAY water heater
- Hand Fed Coal Stove: Warm Morning 414A
- Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
- Other Heating: Ground Source Heat Pump and some Solar
Hey Graham, Is that a typo that you are in Asheville, BC?
-
- Member
- Posts: 1137
- Joined: Fri. Feb. 12, 2016 2:36 pm
- Hand Fed Coal Boiler: Harman SF360
- Hand Fed Coal Stove: T.O.M (Warm Morning converted to baseburner by Steve) Round Oak 1917 Door model O-3, Warm Morning 400, Warm Morning 524, Warm Morning 414,Florence No.77, Warm Morning 523-b
- Hand Fed Coal Furnace: Clayton 7.1/DS Machine basement stove/ Harman SF1500
- Baseburners & Antiques: Renown Parlor stove 87B
- Coal Size/Type: Bituminous/anthracite
- Other Heating: Harman Accentra, enviro omega, Vermont Ironworks Elm stove, Quadrafire Mt Vernon, Logwood stove, Sotz barrel stove,
I burned wood in a warm morning 617. Basically it is a 400 without the shroud.
It burned wood great. Threw a lot of heat. Two drawbacks. It burned wood great... lol. A lot of wood. And it’s a pain to load being a vertical stove. Cutting the wood into chunks instead of splits seemed to help.
If you don’t want to buy coal yet burn the wood. Or buy and burn coal now and save the wood for the shoulder season.
It burned wood great. Threw a lot of heat. Two drawbacks. It burned wood great... lol. A lot of wood. And it’s a pain to load being a vertical stove. Cutting the wood into chunks instead of splits seemed to help.
If you don’t want to buy coal yet burn the wood. Or buy and burn coal now and save the wood for the shoulder season.
-
- New Member
- Posts: 3
- Joined: Thu. Dec. 24, 2020 10:44 pm
- Location: Asheville NC
- Hand Fed Coal Stove: Warm Morning 400A
Ha ha, yes it’s a typo it should say Asheville NC. Fat fingers on an iPhone and autocorrect. And it’s cold right now,12 degrees F, although I’m sure that’s warm for some of the folks on this forum.
I’m good with getting coal. But the old owner left me 2 cords of wood so thought if the stove is in good state it just makes sense to use the wood. No point paying out when I don’t need to.
Thanks for the tip on cutting the wood up more.
I’m good with getting coal. But the old owner left me 2 cords of wood so thought if the stove is in good state it just makes sense to use the wood. No point paying out when I don’t need to.
Thanks for the tip on cutting the wood up more.