Thick ashes blocks air. Not enough air not much fire.
Pea coal takes some good amount of effort for ash removal.
Half fire means you only got ash remove where the half fire remained.
The other half has ashes yet to be removed and is still blocking the air.
Coal Stove Help in NE Bombogenesis!
- McGiever
- Member
- Posts: 10130
- Joined: Sun. May. 02, 2010 11:26 pm
- Location: Junction of PA-OH-WV
- Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
- Hand Fed Coal Boiler: BUCKET A DAY water heater
- Hand Fed Coal Stove: Warm Morning 414A
- Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
- Other Heating: Ground Source Heat Pump and some Solar
- ASea
- Member
- Posts: 1156
- Joined: Thu. Nov. 27, 2014 8:55 pm
- Location: Athol Massachusetts
- Hot Air Coal Stoker Stove: Alaska Kast Console II
- Hand Fed Coal Stove: Coal Chubby
- Baseburners & Antiques: Glenwood Modern Oak 114, Glenwood 30 "Estate" Warm Morning 120
- Coal Size/Type: Sherman Anthracite Nut/Stove from C&T Coal
- Other Heating: Peerless Boiler with Cast Iron Baseboards
Trade it for a Chubby! Pictures always help us to know whats going on with your stove. Stay warm!
-
- Member
- Posts: 118
- Joined: Wed. Dec. 29, 2010 1:42 am
Hello,
As everyone else has mentioned, never disturb a low fire. Only fire I’ve ever lost (and had to start over) was because of thinking, “Hey, I’ll shake the ash out, and more air will flow to liven it up!” Lol
While theoretically true, a low fire is best brought up by first increasing air, then slowly adding a bit of coal to refresh. Then, when healthy again, go ahead and shake.
Learning how much to shake is a curve, too, but you’ll get it. As others have said, I get down low and look at the underside of the grates for an even glow. The suggestion about occasional “cutting” from above sometimes works, too. If you’ve shaken until embers fall and there’s still a dead spot or two, that’s when manually poking those areas usually helps. Paul’s point about shaking a bit afterward to settle the bed is great, too. Don’t want any empty pockets in the bed.
Also, for overnight, pack as much coal in as she’ll fit. I know if I don’t fill mine fill enough on a cold night, she’ll have a ring of ash all around the perimeter and only be glowing in the very center.
Hope this helps, stay warm!
Joe
As everyone else has mentioned, never disturb a low fire. Only fire I’ve ever lost (and had to start over) was because of thinking, “Hey, I’ll shake the ash out, and more air will flow to liven it up!” Lol
While theoretically true, a low fire is best brought up by first increasing air, then slowly adding a bit of coal to refresh. Then, when healthy again, go ahead and shake.
Learning how much to shake is a curve, too, but you’ll get it. As others have said, I get down low and look at the underside of the grates for an even glow. The suggestion about occasional “cutting” from above sometimes works, too. If you’ve shaken until embers fall and there’s still a dead spot or two, that’s when manually poking those areas usually helps. Paul’s point about shaking a bit afterward to settle the bed is great, too. Don’t want any empty pockets in the bed.
Also, for overnight, pack as much coal in as she’ll fit. I know if I don’t fill mine fill enough on a cold night, she’ll have a ring of ash all around the perimeter and only be glowing in the very center.
Hope this helps, stay warm!
Joe
-
- Member
- Posts: 6451
- Joined: Mon. Apr. 16, 2007 9:34 pm
- Location: Central Maine
- Hand Fed Coal Stove: DS Machine 1300 with hopper
- Coal Size/Type: Blaschak Anthracite Nut
- Other Heating: Oil hot water radiators (fuel oil); propane
One more suggestion for night. When you make a bathroom trip in the middle of the night, do a light shaking of the grates. Actually I do that in the daytime, too, every three or four hours if I happen to think of it. Helps clear a few ashes and settle the coal a little more. No need to go through all the rest of the ash-clearing process -- just make sure the ash pan does not fill up to the bottom of the grates, which can burn out the grates.jschaefer7406 wrote: ↑Thu. Jan. 04, 2018 11:25 pmAlso, for overnight, pack as much coal in as she’ll fit. I know if I don’t fill mine fill enough on a cold night, she’ll have a ring of ash all around the perimeter and only be glowing in the very center.
I don't bother with the intermediate shakings in spring and fall when the stove is throttled back to low temperature. But it seems to help when I want lots of heat.
- freetown fred
- Member
- Posts: 30302
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
You & me both DD!!!!!!!