Antique Potbelly Stove Installation
Hi,
First time poster and first time burning coal. I picked up this tiny Orr Aetna No 10 and plan on using it to heat my 400 SF Woodshop. The patent date is 1868.
Will pea or nut coal work better in a stove like this?
I plan on using a 6" Duravent triple wall through the ceiling/roof kit and Supervent Black Insulated pipe from Lowes between the stove and the ceiling box. Any suggestions on how I can attached the oval stove outlet to the black pipe?
Any other tips are appreciated.
Thanks,
Travis
First time poster and first time burning coal. I picked up this tiny Orr Aetna No 10 and plan on using it to heat my 400 SF Woodshop. The patent date is 1868.
Will pea or nut coal work better in a stove like this?
I plan on using a 6" Duravent triple wall through the ceiling/roof kit and Supervent Black Insulated pipe from Lowes between the stove and the ceiling box. Any suggestions on how I can attached the oval stove outlet to the black pipe?
Any other tips are appreciated.
Thanks,
Travis
- freetown fred
- Member
- Posts: 30300
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
I'm thinkin ya can probably squeeze, finagle, etc--crimped end down.
-
- Site Moderator
- Posts: 11417
- Joined: Wed. Nov. 05, 2008 5:11 pm
- Location: Kent CT
- Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
- Baseburners & Antiques: Glenwood Modern Oak 114
- Coal Size/Type: nut and pea
Use double wall insulated for the through the ceiling and up. the triple wall runs too cool.
Use single wall from stove to ceiling.
Wrap a piece of string around the oval outlet and measure it. If it is about 19 inches you can squeeze a 6 inch pipe on it.
Do instal a manual pipe damper or a barometric one.
Use single wall from stove to ceiling.
Wrap a piece of string around the oval outlet and measure it. If it is about 19 inches you can squeeze a 6 inch pipe on it.
Do instal a manual pipe damper or a barometric one.
- Sunny Boy
- Member
- Posts: 25729
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Welcome ttf.
For coal size, it depends. Each stove setup is unique.
If the stove has air leaks under the firebed, as some potbelly stoves do, or if your chimney draft is overly strong, then the denser packing pea size can help slow and control the burn rate.
Some stoves do well on a mix of pea and nut to help control the burn rate.
If your stove is tight, or the draft not so strong, the nut coal with it's larger spaces between chunks will breath and burn better.
Because it's easier to get a good firebed going, I'd start with just nut coal over a really hot bed of BBQ charcoal or wood embers. Then, after a few hours, if it gets too hot for you to control the heat output with just using the primary damper ( in ash pan door), and the pipe damper, then experiment with mixing in pea coal later after you learn more about how the stove will respond with your setup.
Paul
For coal size, it depends. Each stove setup is unique.
If the stove has air leaks under the firebed, as some potbelly stoves do, or if your chimney draft is overly strong, then the denser packing pea size can help slow and control the burn rate.
Some stoves do well on a mix of pea and nut to help control the burn rate.
If your stove is tight, or the draft not so strong, the nut coal with it's larger spaces between chunks will breath and burn better.
Because it's easier to get a good firebed going, I'd start with just nut coal over a really hot bed of BBQ charcoal or wood embers. Then, after a few hours, if it gets too hot for you to control the heat output with just using the primary damper ( in ash pan door), and the pipe damper, then experiment with mixing in pea coal later after you learn more about how the stove will respond with your setup.
Paul
- Sunny Boy
- Member
- Posts: 25729
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Typically the gaps in nut coal grates are about 1/2 to 5/8 inch wide. Those look like rather large spaces to run just straight pea coal. You might have a lot of unburned coal dropping through the grate.
I'd try nut first and then a mix of nut and pea. The nut coal will help hold more of the pea coal in the firebed.
If you only want to buy one size, then I'd say just use nut coal.
Paul
I'd try nut first and then a mix of nut and pea. The nut coal will help hold more of the pea coal in the firebed.
If you only want to buy one size, then I'd say just use nut coal.
Paul
- michaelanthony
- Member
- Posts: 4550
- Joined: Sat. Nov. 22, 2008 10:42 pm
- Location: millinocket,me.
- Hand Fed Coal Stove: Vigilant 2310, gold marc box stove
- Hand Fed Coal Furnace: Gold Marc Independence
- Baseburners & Antiques: Home Sparkle 12
- Coal Size/Type: 'nut
- Other Heating: Fujitsu mini split, FHA oil furnace
Hi Travis, based on your first pic the oval is approx. 5 inches long so that counts out 6 inch pipe. I wouldn't be surprised if a 4 inch pipe can be squeezed around that oval. a 4 inch pipe has a circumference of a hair over 12 and a half inches.
-
- Site Moderator
- Posts: 11417
- Joined: Wed. Nov. 05, 2008 5:11 pm
- Location: Kent CT
- Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
- Baseburners & Antiques: Glenwood Modern Oak 114
- Coal Size/Type: nut and pea
Measure the circumference with a piece of string and then divide that number by 3.1416 to get the round pipe size.
- michaelanthony
- Member
- Posts: 4550
- Joined: Sat. Nov. 22, 2008 10:42 pm
- Location: millinocket,me.
- Hand Fed Coal Stove: Vigilant 2310, gold marc box stove
- Hand Fed Coal Furnace: Gold Marc Independence
- Baseburners & Antiques: Home Sparkle 12
- Coal Size/Type: 'nut
- Other Heating: Fujitsu mini split, FHA oil furnace
-
- Member
- Posts: 28
- Joined: Tue. Feb. 28, 2023 4:33 am
- Location: West Allis WI
- Hand Fed Coal Stove: King Oak 19B
- Coal Size/Type: Anthracite Nut
- Other Heating: Harman Absolute43 wood pellet. Lamppa Kuuma Vapor-Fire 200 gasification wood furnace.
Measured with a wire. 6.286” outside and 5.172” inside. Since there is a hole in the stove flange, the male end must be inserted. The oval width is 3.75” and length is 6.75”. Woodmanspartsplus.com doesn’t sell that size. Who sells 5” oval to 5” round?
- Sunny Boy
- Member
- Posts: 25729
- Joined: Mon. Nov. 11, 2013 1:40 pm
- Location: Central NY
- Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
- Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
- Coal Size/Type: Nuts !
- Other Heating: Oil &electric plenum furnace
Contact member Dana (Dlapan). He said he can make up stove pipes to fit oval to round.
https://www.lapansantiquestoves.com/
Paul
https://www.lapansantiquestoves.com/
Paul