Need some Hitzer 50-93 guidance please

 
User avatar
freetown fred
Member
Posts: 30293
Joined: Thu. Dec. 31, 2009 12:33 pm
Location: Freetown,NY 13803
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut

Post by freetown fred » Sat. Dec. 16, 2017 6:31 pm

In a prior post I said that once a person gets a feel for what their stove can & cannot do, I think it's about a lot of knowledge of your stove & common sense. I for one can't be affording new grates or anything else for that matter. I can only speak on my experience with my particular stove. Except for the basics I've learned here, I try & stay away from suggestions that might be detrimental (cool word) LOL especially to the new comer. As for my cuff mos. I don't fire, (actually I never fire unless I've gotten stupid & am about to lose the fire) when I add coal through the empty hopper I've always got a good bed of coals after shaking. Even then I'm tending at 12 hr intervals.

 
User avatar
hotblast1357
Member
Posts: 5657
Joined: Mon. Mar. 10, 2014 10:06 pm
Location: Peasleeville NY
Stoker Coal Boiler: 1984 Eshland S260 coal gun
Coal Size/Type: Lehigh anthracite pea
Other Heating: air source heat pump, oil furnace

Post by hotblast1357 » Sat. Dec. 16, 2017 6:52 pm

Exactly my point Fred, don’t give bad advice.

Running a hopper fed stove without coal in the hopper is not good, and can cause damage to the hopper.

 
User avatar
freetown fred
Member
Posts: 30293
Joined: Thu. Dec. 31, 2009 12:33 pm
Location: Freetown,NY 13803
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut

Post by freetown fred » Sat. Dec. 16, 2017 7:38 pm

HB, I wasn't giving advice, I was responding to your posts. Also, can't imagine a normal (not fired to tears, which in my opinion should never be done) bed of coal harming the hopper in the 50-93 in the cuff months. Least it hasn't effected mine in 10 yrs of use.


 
User avatar
warminmn
Member
Posts: 8110
Joined: Tue. Feb. 08, 2011 5:59 pm
Location: Land of 11,842 lakes
Hand Fed Coal Stove: Chubby Junior, Efel Nestor Martin, Riteway 37
Coal Size/Type: nut and stove anthracite, lignite
Other Heating: Wood and wear a wool shirt

Post by warminmn » Sun. Dec. 17, 2017 12:21 am

Yep, its all about learning to use the stove that you have.

 
jw157
New Member
Posts: 5
Joined: Tue. Dec. 12, 2017 8:20 pm
Location: Hudson Valley NY
Hand Fed Coal Stove: Hitzer 50-93
Coal Size/Type: Nut

Post by jw157 » Wed. Dec. 20, 2017 8:32 pm

Well it’s been a week and the stove is still going fine, the longest I’ve been able to run it so far, no ash build up on top and no signs of going out on me, finger crossed it will stay burning all winter without issues, thanks to all those who gave me advice as I certainly needed it!

JW

 
DENNIS BAUER
Member
Posts: 283
Joined: Tue. Jan. 13, 2015 8:49 am
Location: Springwater NY, (Western NY)
Hot Air Coal Stoker Stove: Keystoker 105 - SOLD
Hand Fed Coal Stove: Hitzer 30-95 - Garage
Hand Fed Coal Furnace: HITZER 50-93 - HOUSE
Coal Size/Type: NUT
Other Heating: PROPANE FURNACE, ELECTIC BASE BOARD, AND WOOD FIRE PLACE

Post by DENNIS BAUER » Wed. Dec. 20, 2017 8:43 pm

JW, I don't mean to hijack your thread but I'm new to the 50-93 this year, this has been a big help! Mine it's running like a champ, I actually started closing my ash pan door down to slow down the idle when not calling for heat. Got it to idle at 250° and cut my coal usage in half. Now mind you I have a manometer and am still running .08 on a warm day. Think I might need to close the MPD a little.

I really enjoy this thing and this site!


 
User avatar
coalmaster
Member
Posts: 127
Joined: Thu. Dec. 17, 2015 9:47 pm
Location: slate belt
Hand Fed Coal Furnace: hitzer 50-93 2800sqft
Coal Size/Type: nut anthricite

Post by coalmaster » Wed. Dec. 20, 2017 8:57 pm

I'll say ff knows his stuff. He set me on the right track. Now I just use the spade around the front and sides every so often. No more poking, no need to get cute with it. It's so clean now I had to lower my setting

Attachments

15138214564601293471214.jpg
.JPG | 331.5KB | 15138214564601293471214.jpg

 
User avatar
freetown fred
Member
Posts: 30293
Joined: Thu. Dec. 31, 2009 12:33 pm
Location: Freetown,NY 13803
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut

Post by freetown fred » Wed. Dec. 20, 2017 9:48 pm

Crap C, I got one of them thar implements & am gonna try it out tomorrow. Outstanding call my friend. Never to old to learn new stuff!! :)

 
User avatar
gjambor
Member
Posts: 55
Joined: Sat. Jan. 07, 2012 7:39 am
Location: Southern New Jersey
Hot Air Coal Stoker Stove: Alaska Channing III
Hand Fed Coal Stove: Hitzer 30-95
Coal Size/Type: RICE COAL/ nut coal
Other Heating: HEAT PUMP

Post by gjambor » Sat. Dec. 30, 2017 9:32 am

I think my Hitzer is easy to operate. Fly ash should do just that, fly out of the stove. My 30-95 gets some minor ash accumulation on the edges after 12 to 16 hrs. I just poke around the edges from the top, then shake very quickly. The burning coals almost seem like they float when I shake. Then I pick at the grate from below. When I can see light thru the majority of holes I know I'm good. Check your draft . My chimney pulls very strong. On extremely cold days I use my MPD to slow heat loss thru the chimney. This is my 3rd season with this stove. It takes a while to get to know the little things that will make things easier.

 
User avatar
freetown fred
Member
Posts: 30293
Joined: Thu. Dec. 31, 2009 12:33 pm
Location: Freetown,NY 13803
Hand Fed Coal Stove: HITZER 50-93
Coal Size/Type: BLASCHAK Nut

Post by freetown fred » Sat. Dec. 30, 2017 11:02 am

Sounds real good G. Looks like ya found a friend with the 30-95! :)

Post Reply

Return to “Hand Fired Coal Stoves & Furnaces Using Anthracite”