Hitzer 30-95 Question
-
- New Member
- Posts: 3
- Joined: Sun. Dec. 29, 2013 9:23 pm
- Location: Western NY
- Hand Fed Coal Boiler: Chappee
- freetown fred
- Member
- Posts: 30302
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
Take a 15/16 (I think) flat washer & slip it over that nub--might have to file it some to fit--attach to stove body w/ hi-temp silicone or JB Weld--if you don't block it w/ something you'll always have a hot spot there in the fire box.
Attachments
- Stoker6268
- Member
- Posts: 605
- Joined: Mon. Feb. 09, 2009 4:49 pm
- Location: Grafton NH
- Hand Fed Coal Stove: Hitzer 50-93
- Coal Size/Type: Pea
Did the same on my 50-93 as FF did.
No more hot spot!
Home Depot didnt have anything big enough. Found it at Tractor Supply Store.
No more hot spot!
Home Depot didnt have anything big enough. Found it at Tractor Supply Store.
Attachments
- fastcat
- Member
- Posts: 444
- Joined: Thu. Nov. 12, 2009 11:50 pm
- Location: CNY (McGraw)
- Hand Fed Coal Stove: Hitzer 50-93
- Coal Size/Type: Blaschak Nut/Stove Mix
You need a washer with a 1" hole and you will need to file the hole square to just slip over the grate nub, slide it up against the stove then slide the handle up against the washer and tighten the handle with two set screws which you need to put in the handle. Gluing the washer isn't going to do much good beings as the washer rotates with the grate.
- oliver power
- Member
- Posts: 2970
- Joined: Sun. Apr. 16, 2006 9:28 am
- Location: Near Dansville, NY
- Stoker Coal Boiler: KEYSTOKER Kaa-2
- Hand Fed Coal Stove: Hitzer 50-93 & 30-95, Vigilant (pre-2310), D.S. 1600 Circulator, Hitzer 254
WOW!, A square shaft, through a round hole. Seems to me that my grate came through round, then went square. I'll have to look tomorrow morning. I too did the washer trick. I remember thinking it was petty, but did it anyways. A round shaft through a round hole would make it petty. Forgot to look. I'll try again tomorrow.
Last edited by oliver power on Mon. Nov. 09, 2015 8:32 pm, edited 2 times in total.
-
- Member
- Posts: 528
- Joined: Sat. Jul. 06, 2013 6:06 pm
- Location: Northeastern Ct.
- Hand Fed Coal Stove: Hitzer 50-93
- Coal Size/Type: Mostly nut, some pea
Another option is to cut a couple "gaskets" out of 1/8" insulation mat. The space between the shaker handle mount & the stove body on my 3 year old 50-93 is small enough that the handle mount holds them tight to the stove.
- oliver power
- Member
- Posts: 2970
- Joined: Sun. Apr. 16, 2006 9:28 am
- Location: Near Dansville, NY
- Stoker Coal Boiler: KEYSTOKER Kaa-2
- Hand Fed Coal Stove: Hitzer 50-93 & 30-95, Vigilant (pre-2310), D.S. 1600 Circulator, Hitzer 254
Hello Members. I finally remembered to look at my 30-95 grate shaft tonight. Yes, it is a round shaft, coming through a round hole. The very end is square for shaker handle. No wonder I thought the opening around the grate shaft was petty. I took a picture, and sent it to my computer. When it gets here, I'll post it. Last time I sent pictures to the computer, they showed up 2 or 3 hours later. Now I'm curious about my 50-93 grate shaft. I'll check next time I'm down to the old home stead.
Last edited by oliver power on Thu. Nov. 12, 2015 6:25 am, edited 1 time in total.
- freetown fred
- Member
- Posts: 30302
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
My 50-93 is round thru the stove body -- last inch or so is square for handle to slip on.
- oliver power
- Member
- Posts: 2970
- Joined: Sun. Apr. 16, 2006 9:28 am
- Location: Near Dansville, NY
- Stoker Coal Boiler: KEYSTOKER Kaa-2
- Hand Fed Coal Stove: Hitzer 50-93 & 30-95, Vigilant (pre-2310), D.S. 1600 Circulator, Hitzer 254
You just saved me a trip Fred. I'll assume my 50-93 is the same, and not a square shaft through a round hole. Otherwise, I know I would have done something about it.freetown fred wrote:My 50-93 is round thru the stove body -- last inch or so is square for handle to slip on.
- freetown fred
- Member
- Posts: 30302
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
Soooo J, what the hell did you end up doin???