Needing Parts for a Kenmore Coal Stove. 119100120

Modern and vintage hand fired coal stove are similar to a wood stove and in some cases can burn either. They need to be regulated and fed by hand usually every 12 to 24 hours depending on your usage. They require no power to operate making them ideal for rural settings with long power outages.
Post Reply
Brad
New Member
Posts: 1
Joined: Mon. Mar. 10, 2014 8:42 pm

Post Mon. Mar. 10, 2014 9:03 pm

Iam trying to figure out what type of piping does it take from top of stove up. The opening is oval shaped.....so far I havent found anything that works....its an antique kenmore coal stove 119100120

User avatar
Dennis
Member
Posts: 1066
Joined: Sun. Oct. 30, 2011 5:44 pm
Hand Fed Coal Boiler: AHS/WOC55-multi-fuel/wood,oil,coal
Coal Size/Type: Anthracite/stove size
Location: Pottstown,Pa

Post Mon. Mar. 10, 2014 9:22 pm

Welcome Brad,are you looking for a oval to round cast iron stove pipe.
http://chubbystove.com/gallery2.htm
Call to see if the dimentions are correct

dhansen
Member
Posts: 228
Joined: Mon. Dec. 10, 2012 3:51 pm
Stove/Furnace Make: Glenwood No.6 and No.116
Location: Spruce Head, Maine

Post Mon. Mar. 10, 2014 10:06 pm

Brad, if you can show us a couple of photos of the top of your stove we'd have a better chance of finding a solution.

Visit Hitzer Stoves

User avatar
rockwood
Member
Posts: 1371
Joined: Sun. Sep. 21, 2008 7:37 pm
Hot Air Coal Stoker Furnace: Stokermatic coal furnace
Hand Fed Coal Stove: Rockwood Stoveworks Circulator
Baseburners & Antiques: Malleable/Monarch Range
Coal Size/Type: Soft coal: Lump and stoker (slack coal)
Location: Utah

Post Mon. Mar. 10, 2014 11:21 pm

If you're not sure of the size pipe needed to match the oval outlet of the stove, this post gives the circumferences of common stove pipe sizes so you can measure the oval to determine the size you need.

New Stove Question

I never use any special oval to round adapter, I just squeeze the stove pipe to an oval shape and slide it on the oval outlet of the stove. I always use "blue steel stove pipe" for this application because it's a thinner gauge and easier to work with but most hardware stores don't carry it anymore so you might have trouble finding it locally.
If you're planning to use the heavier gauge black stove pipe commonly sold at hardware stores, it will be harder to manipulate to an oval shape to fit the stove, so an adapter would be easier in that case.
"None are more hopelessly enslaved than those who falsely believe they are free." -Goethe

Sunny Boy
Member
Posts: 12600
Joined: Mon. Nov. 11, 2013 1:40 pm
Hand Fed Coal Boiler: Anthracite Industrial, domestic hot water heater
Baseburners & Antiques: Glenwood range 208, # 6 base heater, 2 Modern Oak 118.
Coal Size/Type: Nuts !
Other Heating: Oil &electric plenum furnace
Location: Central NY

Post Tue. Mar. 11, 2014 5:39 am

Wrap a piece of string around the pipe collar and make a mark where the end of the string meets the rest of the string. Then measure the length of string to the mark.

See which of the numbers that Rockwood posted is closest to that length.

If it's an oddball size, Bryant Stove in Maine can make a tapered pipe section for you.

Paul
So many stoves - so few chimneys. I must be coal-stone crazy.

Post Reply

Return to “Hand Fired Coal Stoves & Furnaces Using Anthracite”