Gibratar CFS
-
- Member
- Posts: 1769
- Joined: Tue. Feb. 19, 2013 3:30 pm
- Location: Mystic CT
- Hand Fed Coal Stove: Crane 404
- Contact:
I have a line on a used one and the current owner is putting together the coal grates have everything there. The current big search is for the coal banking plate anf the link that connects all the grates. Is there a source of used parts and any reason why I can not make the link and banking plate. I am assuming the link is steel and while I do not want to make a banking plate out of cast is there any reason 1018 steel would not work? A bew one is arount 110 plus shipping according to a couple places on the net that have old stock. I can easily get plate steel cut to size from 3/16 to 1/2 and if bosses need to be welded on that can happen though gets close to the price of new but a backup position if the part is not really available.
The thing looks like a beast at 485 lbs and does not have the fan option or a place to put it. I am looking to heat 1000 sq ft so the obvious question is how low can it go and what burn times should I expect?
Oh and a suggestion on a fair price assuming they find all the parts and do not have to buy any other than fresh bricks and door gasket? I do not mean the steal it price but the fair price if all there no cracks etc and the previous parts and a can of paint..
Here are the grate parts they found so far. Where does the box go with the tubes as it is not in the user manual?
Dave.
The thing looks like a beast at 485 lbs and does not have the fan option or a place to put it. I am looking to heat 1000 sq ft so the obvious question is how low can it go and what burn times should I expect?
Oh and a suggestion on a fair price assuming they find all the parts and do not have to buy any other than fresh bricks and door gasket? I do not mean the steal it price but the fair price if all there no cracks etc and the previous parts and a can of paint..
Here are the grate parts they found so far. Where does the box go with the tubes as it is not in the user manual?
Dave.
- McGiever
- Member
- Posts: 10130
- Joined: Sun. May. 02, 2010 11:26 pm
- Location: Junction of PA-OH-WV
- Stoker Coal Boiler: AXEMAN-ANDERSON 130 "1959"
- Hand Fed Coal Boiler: BUCKET A DAY water heater
- Hand Fed Coal Stove: Warm Morning 414A
- Coal Size/Type: PEA,NUT,STOVE /ANTHRACITE
- Other Heating: Ground Source Heat Pump and some Solar
Picture makes it hard to tell...but tubes prolly have something to do w/ bricks...retainers or supports...my best guess.
If the stove is in good shape you have found a gem. In my humble opinion the Gibraltar is the best modern handfired out there. You can probably pick it a up a little cheaper than a Harman because not alot of people know first hand how good they are. If you can pick up a decent used one for under 450 I think you are ahead of the game. Very long burn times, the CFS can hum along at high temps all day long You don't need a blower with this stove , it will also idle down without going out. Word association Gibraltar=Tank
- dtzackus
- Member
- Posts: 288
- Joined: Tue. Jul. 08, 2008 6:36 pm
- Location: Schuylkill County, PA
- Hand Fed Coal Stove: Gibraltar LCC
I have a copy of the Gibratar manual which shows all the models, I own a LCC, the monster. I'll post the manual when I get home later today. Dan
You should try a search for Gibratar, I am sure you could find the manual that method, if not I'll post it later...
You should try a search for Gibratar, I am sure you could find the manual that method, if not I'll post it later...
-
- Member
- Posts: 1769
- Joined: Tue. Feb. 19, 2013 3:30 pm
- Location: Mystic CT
- Hand Fed Coal Stove: Crane 404
- Contact:
Thanks for the manual. They finally had a chance to see if all the grate parts are there. All is there other than the plate that goes in front of the glass I am assuming it is made of cast iron and looks like it just drops in to some slots. If I made one out of steel possibly 1018 or 1020 would that work as a little piece of steel is cheap compared to the cast part they are asking 110 bucks for a flat plate. Any advise would be very helpful. Dave
-
- Member
- Posts: 1769
- Joined: Tue. Feb. 19, 2013 3:30 pm
- Location: Mystic CT
- Hand Fed Coal Stove: Crane 404
- Contact:
That is why I am thinking about making them out of steel plate from a scrap yard way cheaper if it will work. Any idea if this is a problem. Finally going to take a look at it and buy it if they will come down a bit in price to help cover the missing parts.dtzackus wrote:The two plates are called banking plates, you will need two to have enough coal to get thru the night.
I saw them on a few website, kinda $$$. Good luck!
- dtzackus
- Member
- Posts: 288
- Joined: Tue. Jul. 08, 2008 6:36 pm
- Location: Schuylkill County, PA
- Hand Fed Coal Stove: Gibraltar LCC
Make sure you use cast, I think anything else would crack...esp for the bottom one, top one you "might" be able to get away with not using cast iron.
Good luck, let me know how it works, my top on was bent when I bought mine.
Dan
Good luck, let me know how it works, my top on was bent when I bought mine.
Dan
-
- Member
- Posts: 1769
- Joined: Tue. Feb. 19, 2013 3:30 pm
- Location: Mystic CT
- Hand Fed Coal Stove: Crane 404
- Contact:
I was thinking the opposite in that I can bend steel and not cast so steel less likely to crack though could burn through but the melting point of carbon steel is 300 to 500 degrees higher than grey cast iron.dtzackus wrote:Make sure you use cast, I think anything else would crack...esp for the bottom one, top one you "might" be able to get away with not using cast iron.
Good luck, let me know how it works, my top on was bent when I bought mine.
Dan
Thanks for the tip on yours being bent I will bring a straight edge with me.
Dave