Using anthracite or bituminous coal for residential and commercial heating.
https://coalpail.com/coal-forum/
Ok, thanks! I will search "stove temperature" and "stack temperature" to see what I come up with!WNY wrote:it can vary from 200-500+ degrees depending on where you are measuring it and how hot you are burning it.
Each stove is different.
Also, for proper drafting, you need to have a draft gauge and set you draft accordingly for optimum heat. Too much draft you can be pulling heat out of the stove. Too little, you can CO buildup.
There are a lot of threads on here on Stove Temperatures, Stack Temperatures, etc.....
You have a stoker so your acceptable temp is what it will go to with out pushing hot coals off the burn grate, at max fire you should have about an inch of ash. You will not see good temps though if your power vent is sucking to hard it will pull all the heat out of the stoker.94Bison wrote:How hot should the stove burn? I bought a stove thermometer and was interested in what is the accepted burn temp. Also, what adjustments can be made if it is not burning hot enough? Open/close damper more, adjust powerventer? Are there any other adjustments that can be made? Thanks in advance for any input!
Too many questions all at once, Ted, without enough background information. Are you thinking of anthracite coal or bituminous? Big difference, looks like your stove can handle both.... Sounds like you should have plenty of draft. Most coal burners do use a barometric damper, but not for wood! Many also use the old-fashioned pipe damper along with the baro, some use only one or the other. A manometer can help, can't hurt. Use the forum search (upper right) to explore the topics, spend some time browsing and reading especially in the Hand Fed Stove section. Also search the "bituminous" threads if that's the type of coal you have access to. Then maybe post a new thread or two to focus in on specific questions. Sorry, I'm not trying to put you off, just don't have enough information to really address your questions and don't want to steer you wrong.ted1111 wrote:new to site and this type of communication just installed a wonder lux wood - coal stove burning wood now I have no damper at all thats not right is it ??damper should be closest to stove or up on pipe away from fire box?? burning alot of wood but great heat ! 25ft of 6" flu on vertical seems good draft do I need a barometric damper?? and mano meter ??dose mano meter have a remote sensor 6 or 8 ft long???? also can I add coal to a wood fire maby large lump for long burn??? thanks for shareing your knowledge all best Ted
You have a stoker so your acceptable temp is what it will go to with out pushing hot coals off the burn grate, at max fire you should have about an inch of ash.Coalfire wrote:You have a stoker so your acceptable temp is what it will go to with out pushing hot coals off the burn grate, at max fire you should have about an inch of ash. You will not see good temps though if your power vent is sucking to hard it will pull all the heat out of the stoker.94Bison wrote:How hot should the stove burn? I bought a stove thermometer and was interested in what is the accepted burn temp. Also, what adjustments can be made if it is not burning hot enough? Open/close damper more, adjust powerventer? Are there any other adjustments that can be made? Thanks in advance for any input!
Just a word of warning if your power vent is drawing to hard, and your hopper gets low on coal, you can pull air in through the hopoper and the fire will follow the coal back.
The manometer is very important
Eric
You have a stoker so your acceptable temp is what it will go to with out pushing hot coals off the burn grate, at max fire you should have about an inch of ash.Coalfire wrote:You have a stoker so your acceptable temp is what it will go to with out pushing hot coals off the burn grate, at max fire you should have about an inch of ash. You will not see good temps though if your power vent is sucking to hard it will pull all the heat out of the stoker.94Bison wrote:How hot should the stove burn? I bought a stove thermometer and was interested in what is the accepted burn temp. Also, what adjustments can be made if it is not burning hot enough? Open/close damper more, adjust powerventer? Are there any other adjustments that can be made? Thanks in advance for any input!
Just a word of warning if your power vent is drawing to hard, and your hopper gets low on coal, you can pull air in through the hopoper and the fire will follow the coal back.
The manometer is very important
Eric
You should not have to adjust your feed rate. You should set your base feed rate so at a constant run you have an inch of ash at the end of the grate. That way when you are under operation, when the stove needs to put out max heat it will do so safely. your base setting will not change based on outside temp, could it have not been set correctly before?Joeski wrote:You have a stoker so your acceptable temp is what it will go to with out pushing hot coals off the burn grate, at max fire you should have about an inch of ash.Coalfire wrote: You have a stoker so your acceptable temp is what it will go to with out pushing hot coals off the burn grate, at max fire you should have about an inch of ash. You will not see good temps though if your power vent is sucking to hard it will pull all the heat out of the stoker.
Just a word of warning if your power vent is drawing to hard, and your hopper gets low on coal, you can pull air in through the hopoper and the fire will follow the coal back.
The manometer is very important
Eric
So Eric if the temperature outside is lower then it has been and the wind is really blowing would the temp of the stove be effected? I'm not sure if I'm asking this question correctly. My stove temp on the out side of the stove above the top door was at around 550 until today when it went to 400 until I increased the feed rate. I hope I'm making sense but it is late and I'm sleepy. Thank you for your knowledge.