Stove Help!!! Need Name and Its Says Model #16 0N Front

Modern and vintage hand fired coal stove are similar to a wood stove and in some cases can burn either. They need to be regulated and fed by hand usually every 12 to 24 hours depending on your usage. They require no power to operate making them ideal for rural settings with long power outages.
Post Reply
meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 9:12 am

IMG_0635.JPG
IMG_0635.JPG
IMG_0625.jpg
IMG_0654.JPG
ok guys back after a while off , onto my second project maybe, well if its worth it here what I was given for free I need info about this tove as much as possible, :?: :?: :?: it has a round shacker handle and also a slide shaker in the side im only missing the ash pan I have the finial and cover also

meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 9:29 am

i have to find out where to get a sat iron 90 cause this one is broke and the size of the ash pane to make one , can some tell me what is the best seam sealer to use and reactory cement ? and the inside looks to have newer bricks in it ? I wanna get the shaker grates sent out to foundry for new ones to be cast , anybody know what that would cost ? the vent on top goes down the inside cylinder to the top of the fire bricks I think, this stove almost looks like a oak andes , what and how do I vent it cause of the 2 vent orts on it , it also has that slide thing under the front door it openes up some air holes under the cylinder , please help with any info , and what material do u guys use to sand blast with abrasive wise?
Attachments
IMG_0632.JPG
more pics
IMG_0640.JPG
IMG_0628.JPG
IMG_0645.JPG
IMG_0628.JPG
IMG_0638.JPG
IMG_0633.JPG
IMG_0643.JPG
IMG_0653.jpg
IMG_0652.JPG

meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 9:35 am

2
Attachments
IMG_0650.JPG

meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 9:36 am

the doors fit super tight , but I need ti find some of those hinge pins and a new cast elbow with air knob on it

Visit Hitzer Stoves

meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 9:41 am

1
Attachments
IMG_0637.JPG
IMG_0626.jpg

meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 9:45 am

more
Attachments
IMG_0647.JPG
more
IMG_0649.JPG
1
IMG_0642.JPG
2

User avatar
Smokeyja
Member
Posts: 1984
Joined: Mon. Nov. 21, 2011 6:57 pm
Baseburners & Antiques: Glenwood #6 baseheater, Richmond Advance Range, WarmMorning 414a x2
Coal Size/Type: Nut / Anthracite
Other Heating: none
Location: Richmond, VA.
Contact:

Post Fri. Nov. 23, 2012 10:22 am

Most of the time you can use basic steel round stock for your hinge pins. Tell me what size you need and I can cut you some and forge a head on them. I use rutlands stove cement and it seals well. Use that and cord where you can. Let me know if you need help recreating any parts if you can't find them.

Is this the first project since you sold the base burner?
Josh http://www.stellarsmithing.com
-Glenwood #6 Base heater - Richmond Advance Range -2 Locke stove co. Warm Morning 414A -Deville express - wood parlour stove
Dance of the Blue Ladies --->http://youtu.be/KfzF47S7bFM?list=UUnshvG_vjY7CT9QKfNuB9dg
Mathew 6:33-34

meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 10:37 am

yes sir it is

Visit Hitzer Stoves

meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 10:40 am

im trying to figure out how this thing works with two outlets ,in going to completely tear this one apart and start fresh wondering how many btus this mama can put out ? it says 16 on the front off the stove

franco b
Site Moderator
Posts: 8442
Joined: Wed. Nov. 05, 2008 5:11 pm
Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
Baseburners & Antiques: Glenwood Modern Oak 114
Coal Size/Type: nut and pea
Location: Kent CT

Post Fri. Nov. 23, 2012 11:19 am

I think you have a double heater. Two skins. There is a space between for hot air to rise and exit the top outlet. Reach under the the ring at the fire pot top and you should feel the opening between the two skins which is the air inlet. The outlet could be piped to an upstairs room if wanted.

meatball
Member
Posts: 99
Joined: Fri. Dec. 10, 2010 9:12 pm
Stove/Furnace Make: harman mark 2
Location: alburtis pa 18011

Post Fri. Nov. 23, 2012 7:40 pm

that could be good , all I knw there is a inner ring the top damper oval one is that where you would pipe it up to a second floor? because whe u turn the damper on it it doesnt close off the little oval holes completely

franco b
Site Moderator
Posts: 8442
Joined: Wed. Nov. 05, 2008 5:11 pm
Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
Baseburners & Antiques: Glenwood Modern Oak 114
Coal Size/Type: nut and pea
Location: Kent CT

Post Fri. Nov. 23, 2012 7:45 pm

meatball wrote:that could be good , all I knw there is a inner ring the top damper oval one is that where you would pipe it up to a second floor? because whe u turn the damper on it it doesnt close off the little oval holes completely
Probably to adjust the output.

Post Reply

Return to “Hand Fired Coal Stoves & Furnaces Using Anthracite”