My Trip to the Chubby Factory.. WOO HOO!
- SMITTY
- Member
- Posts: 12526
- Joined: Sun. Dec. 11, 2005 12:43 pm
- Location: West-Central Mass
- Stoker Coal Boiler: EFM 520 Highboy
- Coal Size/Type: Rice / Blaschak anthracite
- Other Heating: Oil fired Burnham boiler
Careful on your way to Tufts. Grafton police are relentless. Don't sneeze while driving, or have any smashed insects obstructing your vision! Check all firearms at the border, and have papers ready!
Your always welcome here too Fred - just have to give advance notice so we can excavate an extra chair out of my wife's junk pile here ....
Your always welcome here too Fred - just have to give advance notice so we can excavate an extra chair out of my wife's junk pile here ....
Last edited by SMITTY on Tue. Nov. 13, 2012 10:50 am, edited 1 time in total.
- ONEDOLLAR
- Verified Business Rep.
- Posts: 1866
- Joined: Thu. Dec. 01, 2011 6:09 pm
- Location: Sooner Country Oklahoma
- Hand Fed Coal Stove: 2014 Chubby Prototype
- Coal Size/Type: Nut/Anthracite
- Contact:
Fred...Didn't you do the circuit as "Fedora Fred and His Fantastic Phallic Felines"? Wasn't that you? Fred....? Fred....?
We might need to move this thread to Flame Suit Central........
We might need to move this thread to Flame Suit Central........
- freetown fred
- Member
- Posts: 30302
- Joined: Thu. Dec. 31, 2009 12:33 pm
- Location: Freetown,NY 13803
- Hand Fed Coal Stove: HITZER 50-93
- Coal Size/Type: BLASCHAK Nut
Nope, I was free-wheelin Fred out of Easy Rider. Your right, it's gettin close
- whistlenut
- Member
- Posts: 3548
- Joined: Sat. Mar. 17, 2007 6:29 pm
- Location: Central NH, Concord area
- Stoker Coal Boiler: AA130's,260's, AHS130&260's,EFM900,GJ & V-Wert
- Hand Fed Coal Boiler: Franks,Itasca 415,Jensen, NYer 130,Van Wert
- Hot Air Coal Stoker Furnace: Alaska, EFM, Keystoker, Yellow Flame
- Hot Air Coal Stoker Stove: Alaska, Keystoker-2,Leisure Line
- Hand Fed Coal Stove: Alaska, Gibraltar, Keystone,Vc Vigilant 2
- Hand Fed Coal Furnace: Ford, Jensen, NYer, Van Wert,
- Baseburners & Antiques: Glenwoods
- Coal Size/Type: Barley, Buck, Rice ,Nut, Stove
- Other Heating: Oil HWBB
I need to go outside...this is going to new levels. Sorry Larry, for anything derogatory, it in NO WAY reflects your reputation, and the fine products you sell and service.
I guess I'll have to come home early and watch a couple episodes of Dr. Phil as see if I can get my mind right!!!!
I called him last night and all he said was: You need f***ing HELP!!!....whatever that means.
Save a table up front for Fred and I, OD!
I guess I'll have to come home early and watch a couple episodes of Dr. Phil as see if I can get my mind right!!!!
I called him last night and all he said was: You need f***ing HELP!!!....whatever that means.
Save a table up front for Fred and I, OD!
- michaelanthony
- Member
- Posts: 4550
- Joined: Sat. Nov. 22, 2008 10:42 pm
- Location: millinocket,me.
- Hand Fed Coal Stove: Vigilant 2310, gold marc box stove
- Hand Fed Coal Furnace: Gold Marc Independence
- Baseburners & Antiques: Home Sparkle 12
- Coal Size/Type: 'nut
- Other Heating: Fujitsu mini split, FHA oil furnace
.....I think I know what happened to that poor steer in front of the Hill Top restaurant.ONEDOLLAR wrote:Ahhhhh... Now I remember.......
- kstone
- Member
- Posts: 95
- Joined: Wed. Dec. 21, 2011 10:04 am
- Location: plymouth mass
- Baseburners & Antiques: Andes 14 crown
- Coal Size/Type: nut
hmm I am just wondering if Larry can be talked into reproducing the plymouth 14 line I think the stoves where made in the building down on water street in plymouth around 1890 to 1905? they made a 9 up to 14
Attachments
- I'm On Fire
- Member
- Posts: 3918
- Joined: Thu. Jun. 10, 2010 9:34 am
- Location: Vernon, New Jersey
- Hand Fed Coal Stove: DS Machines DS-1600 Hot Air Circulator
Awesome on hanging out with Mr.Trainer. Was going to say this thread is worthless without pics. But if Larry said no then I forgive you.
- ONEDOLLAR
- Verified Business Rep.
- Posts: 1866
- Joined: Thu. Dec. 01, 2011 6:09 pm
- Location: Sooner Country Oklahoma
- Hand Fed Coal Stove: 2014 Chubby Prototype
- Coal Size/Type: Nut/Anthracite
- Contact:
IOF
I wish I could post pics of what I saw but alas Larry asked me not to take photo's and discuss particulars. Trade secrects and I 100% respect that. I feel honored that Larry invited me down.
Keystone
I wish he would as well. Problem is tooling up to make or even remake a stove costs THOUSANDS and THOUSANDS of dollars. Even before 1 stove is sold. The wood molds alone for a firepot can be upwards of $10k. Let alone the cost of casting. UL testing isn't cheap either.
I wish I could post pics of what I saw but alas Larry asked me not to take photo's and discuss particulars. Trade secrects and I 100% respect that. I feel honored that Larry invited me down.
Keystone
I wish he would as well. Problem is tooling up to make or even remake a stove costs THOUSANDS and THOUSANDS of dollars. Even before 1 stove is sold. The wood molds alone for a firepot can be upwards of $10k. Let alone the cost of casting. UL testing isn't cheap either.
- michaelanthony
- Member
- Posts: 4550
- Joined: Sat. Nov. 22, 2008 10:42 pm
- Location: millinocket,me.
- Hand Fed Coal Stove: Vigilant 2310, gold marc box stove
- Hand Fed Coal Furnace: Gold Marc Independence
- Baseburners & Antiques: Home Sparkle 12
- Coal Size/Type: 'nut
- Other Heating: Fujitsu mini split, FHA oil furnace
Considering the # of people that heated with coal at the turn of the century and beyond, it is freightening to think of the # of beautiful and efficient stoves that were destroyed and worse yet the # of stoves sitting idle sadly not doing their job.
- ONEDOLLAR
- Verified Business Rep.
- Posts: 1866
- Joined: Thu. Dec. 01, 2011 6:09 pm
- Location: Sooner Country Oklahoma
- Hand Fed Coal Stove: 2014 Chubby Prototype
- Coal Size/Type: Nut/Anthracite
- Contact:
M.A.
Yes there are a lot of great old stoves out there. Stoves that could be put to work and saving their owners some serious coin over the oil or gas they continue to use. $300 for a ton of coal would save most people $1000 in heating costs. All for about 10 mins a day in "work" tending the stove. I think many people are just to darn LAZY and have had it too good for too long. Maybe this country needs a second "Great Depression" to wake people up out of their slumber?
Sadly some people seem to have a completely over inflated idea of what these stoves are worth. I see people routinely asking 100% restored prices for units that need a complete top to bottom restoration. Perhaps it is a "North East" thing as it seems almost everything up this way cost double what it should.
I have been in the market for a parlor or perhaps a base burner now for a while. As such I look online daily for them and I am no longer shocked by the amount of money many people seem to think their "antique half rusted burnt out and cracked Glenwood is worth. Most people seem to have a completely over inflated idea of what these stoves are worth. Perhaps it is a "North East" thing as it seems almost everything up this way cost double what it should. Perhaps it is the economy. Sooner or later the right stove will present itself. Could be a Craigslist find or a unit from Doug down at http://www.barnstablestove.com but I will purchase one. Question is when
Yes there are a lot of great old stoves out there. Stoves that could be put to work and saving their owners some serious coin over the oil or gas they continue to use. $300 for a ton of coal would save most people $1000 in heating costs. All for about 10 mins a day in "work" tending the stove. I think many people are just to darn LAZY and have had it too good for too long. Maybe this country needs a second "Great Depression" to wake people up out of their slumber?
Sadly some people seem to have a completely over inflated idea of what these stoves are worth. I see people routinely asking 100% restored prices for units that need a complete top to bottom restoration. Perhaps it is a "North East" thing as it seems almost everything up this way cost double what it should.
I have been in the market for a parlor or perhaps a base burner now for a while. As such I look online daily for them and I am no longer shocked by the amount of money many people seem to think their "antique half rusted burnt out and cracked Glenwood is worth. Most people seem to have a completely over inflated idea of what these stoves are worth. Perhaps it is a "North East" thing as it seems almost everything up this way cost double what it should. Perhaps it is the economy. Sooner or later the right stove will present itself. Could be a Craigslist find or a unit from Doug down at http://www.barnstablestove.com but I will purchase one. Question is when
Last edited by ONEDOLLAR on Thu. Nov. 15, 2012 2:43 pm, edited 1 time in total.
- wsherrick
- Member
- Posts: 3744
- Joined: Wed. Jun. 18, 2008 6:04 am
- Location: High In The Poconos
- Hand Fed Coal Stove: Glenwood Base Heater, Crawford Base Heater
- Baseburners & Antiques: Crawford Base Heater, Glenwood, Stanley Argand
- Coal Size/Type: Chestnut, Stove Size
It is worth the money to go ahead and get one that is restored. I watch on craigslist all of the time for stoves. I have seen a few that were worth the price asked for, but; I have been burned buying stoves without looking at them first. You must look at the stove and examine it completely before buying it. Otherwise, (even if you know what you are doing) you can be had. And yes, it's the same everywhere. If you want to buy something from some individual, what they have is priceless. If you want to sell, then what you have to sell is worthless. I can smell greed a mile away. These people can be greedy all by themselves.ONEDOLLAR wrote:M.A.
Yes there are a lot of great old stoves out there. Stoves that could be put to work and saving their owners some serious coin over the oil or gas they continue to use. $300 for a ton of coal would save most people $1000 in heating costs. All for about 10 mins a day in "work" tending the stove. I think many people are just to darn LAZY and have had it too good for too long. Maybe this country needs a second "Great Depression" to wake people up out of their slumber?
Sadly some people seem to have a completely over inflated idea of what these stoves are worth. I see people routinely asking 100% restored prices for units that need a complete top to bottom restoration. Perhaps it is a "North East" thing as it seems almost everything up this way cost double what it should.
I have been in the market for a parlor or perhaps a base burner now for a while. As such I look online daily for them and I am no longer shocked by the amount of money many people seem to think their "antique half rusted burnt out and cracked Glenwood is worth. Most people seem to have a completely over inflated idea of what these stoves are worth. Perhaps it is a "North East" thing as it seems almost everything up this way cost double what it should. Perhaps it is the economy. Sooner or later the right stove will present itself. Could be a Craigslist find or a unit from Doug down at http://www.barnstablestove.com but I will purchase one. Question is when
All the last posts are real.
Buying an antique stove may be a nice experience for some and a nightmare for other ones. The price must be considered but the stove condition is probably the most important thing to consider. A stove may look to be expensive for someone but correct for the guy wanting that ""exact"" stove. Some models are easier than others to find...so prices are quite hard to compare... when wanting to buy a brand new car even with the same options, it could be surprising to be able to compare 2 cars exactly the same, always this or that ...so when time to find THE stove comes be prepared. For some buying from a well reputed antique shop can be the best buy, for some others buying somewhere else can be part of the Game as can be the restoration job... And finally buying a brand new stove is an other option.
So there is ""room"" for everybody
Buying an antique stove may be a nice experience for some and a nightmare for other ones. The price must be considered but the stove condition is probably the most important thing to consider. A stove may look to be expensive for someone but correct for the guy wanting that ""exact"" stove. Some models are easier than others to find...so prices are quite hard to compare... when wanting to buy a brand new car even with the same options, it could be surprising to be able to compare 2 cars exactly the same, always this or that ...so when time to find THE stove comes be prepared. For some buying from a well reputed antique shop can be the best buy, for some others buying somewhere else can be part of the Game as can be the restoration job... And finally buying a brand new stove is an other option.
So there is ""room"" for everybody
- ONEDOLLAR
- Verified Business Rep.
- Posts: 1866
- Joined: Thu. Dec. 01, 2011 6:09 pm
- Location: Sooner Country Oklahoma
- Hand Fed Coal Stove: 2014 Chubby Prototype
- Coal Size/Type: Nut/Anthracite
- Contact:
wsherrick, nortcan
If the right stove, and mean the RIGHT stove would present itself on CL that stove would first head to Doug or Emery for a top to bottom rehab and chrome before it would ever see a fire at my house. Chances are I will pick one up at Barnstablestove.com . Doug has one now I have my eye on. Might run down next week for some hands and in person viewing. What I would like is Base Burner that can also handle Bit. As I do not plan to live in the North East forever and getting Anthracite out "west" can be problematic sometimes. Anyone have any suggestions for a good Parlor or Base Burner than can handle both? I am all ears.
If the right stove, and mean the RIGHT stove would present itself on CL that stove would first head to Doug or Emery for a top to bottom rehab and chrome before it would ever see a fire at my house. Chances are I will pick one up at Barnstablestove.com . Doug has one now I have my eye on. Might run down next week for some hands and in person viewing. What I would like is Base Burner that can also handle Bit. As I do not plan to live in the North East forever and getting Anthracite out "west" can be problematic sometimes. Anyone have any suggestions for a good Parlor or Base Burner than can handle both? I am all ears.