I Thought I Would Share. Hot Blast #153 Restoration

 
franco b
Site Moderator
Posts: 11025
Joined: Wed. Nov. 05, 2008 5:11 pm
Location: Kent CT
Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
Baseburners & Antiques: Glenwood Modern Oak 114
Coal Size/Type: nut and pea

Post by franco b » Fri. Aug. 05, 2011 1:15 pm

Outstanding pictures. Can really see the condition of the pieces. They don't look rust pitted at all which should make the nickel plating less costly since prep labor is less.


 
grumpy
Member
Posts: 10536
Joined: Sat. Jan. 02, 2010 12:28 am

Post by grumpy » Fri. Aug. 05, 2011 1:33 pm

Thanks guy's, the parts went in today..

 
grumpy
Member
Posts: 10536
Joined: Sat. Jan. 02, 2010 12:28 am

Post by grumpy » Mon. Aug. 08, 2011 12:49 am

Anyone have any ideas as to why the secondary air passage can draw from the ash pan, I have never seen this. Will had a good idea on why, anyone else got any clues?

Attachments

air flow.pdf
.PDF | 15.4KB | air flow.pdf

 
User avatar
SteveZee
Member
Posts: 2512
Joined: Wed. May. 11, 2011 10:45 am
Location: Downeast , Maine
Hand Fed Coal Stove: Glenwood Modern Oak 116 & Glenwood 208 C Range

Post by SteveZee » Mon. Aug. 08, 2011 7:18 am

I think Will is right that it's like a barometric damper per se and lessens the draw. On my Herald there are vents in the back of the ash pit. While not like your stove where the firepot actually has that cast pocket, I think the same effect is achieved. On your's, since it also connects to that ring with the holes, it might also provide heated air for better combustion? (just guessing)

Attachments

Herald (7) (Small).JPG
.JPG | 32.9KB | Herald (7) (Small).JPG

 
grumpy
Member
Posts: 10536
Joined: Sat. Jan. 02, 2010 12:28 am

Post by grumpy » Mon. Aug. 08, 2011 1:10 pm

Thanks for that photo Steve. Looks like I will be learning how to burn the new stove, I still have not got it down with my #77... lol Oh well it should be easier this time since I have half a clue....

 
franco b
Site Moderator
Posts: 11025
Joined: Wed. Nov. 05, 2008 5:11 pm
Location: Kent CT
Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
Baseburners & Antiques: Glenwood Modern Oak 114
Coal Size/Type: nut and pea

Post by franco b » Mon. Aug. 08, 2011 2:48 pm

I think it is to lessen the primary air in high draft conditions that might not be adequately controlled by the vents in the ash pan door. Would aid in maintaining a low burn by diverting air. The air tightness of the ash pan door becomes less important.

This would be a good way to better control a non air tight stove such as a pot belly or cannon stove by adding a divert-er path.

 
grumpy
Member
Posts: 10536
Joined: Sat. Jan. 02, 2010 12:28 am

Post by grumpy » Mon. Aug. 08, 2011 3:43 pm

That seems to make the most sense. Also there is a flap that covers a hole in the loading door. My #77 has that also, maybe this has something to do with it.

Attachments

IMG_4574.JPG
.JPG | 118.3KB | IMG_4574.JPG


 
User avatar
wsherrick
Member
Posts: 3744
Joined: Wed. Jun. 18, 2008 6:04 am
Location: High In The Poconos
Hand Fed Coal Stove: Glenwood Base Heater, Crawford Base Heater
Baseburners & Antiques: Crawford Base Heater, Glenwood, Stanley Argand
Coal Size/Type: Chestnut, Stove Size

Post by wsherrick » Mon. Aug. 08, 2011 5:32 pm

That air inlet in the back of the stove is expressly for the purpose of reducing the primary air draft pull through the fire when needed. I have never seen a design like that where the extra air is sent through the secondary air tubes. It will be very interesting to see how this stove performs. Here is yet another example of the brilliance of our Foundry Fathers. I am continually amazed at them.

 
franco b
Site Moderator
Posts: 11025
Joined: Wed. Nov. 05, 2008 5:11 pm
Location: Kent CT
Hand Fed Coal Stove: V ermont Castings 2310, Franco Belge 262
Baseburners & Antiques: Glenwood Modern Oak 114
Coal Size/Type: nut and pea

Post by franco b » Mon. Aug. 08, 2011 6:53 pm

wsherrick wrote: Foundry Fathers.
I like that.

 
grumpy
Member
Posts: 10536
Joined: Sat. Jan. 02, 2010 12:28 am

Post by grumpy » Mon. Aug. 08, 2011 8:23 pm

Hi Guys, got a couple more done today. Have the grate ready to cast. One more, the base, and I will be done. Just have to wait for the new parts and the plating to be done..

Attachments

IMG_4638.JPG
.JPG | 120.6KB | IMG_4638.JPG
IMG_4644.JPG
.JPG | 164.6KB | IMG_4644.JPG
IMG_4646.JPG
.JPG | 177.4KB | IMG_4646.JPG
IMG_4652.JPG
.JPG | 161.1KB | IMG_4652.JPG
IMG_4656.JPG
.JPG | 180.7KB | IMG_4656.JPG
IMG_4637.JPG
.JPG | 148.9KB | IMG_4637.JPG
Last edited by grumpy on Mon. Aug. 08, 2011 9:21 pm, edited 1 time in total.

 
grumpy
Member
Posts: 10536
Joined: Sat. Jan. 02, 2010 12:28 am

Post by grumpy » Mon. Aug. 08, 2011 8:33 pm

wsherrick wrote:That air inlet in the back of the stove is expressly for the purpose of reducing the primary air draft pull through the fire when needed. I have never seen a design like that where the extra air is sent through the secondary air tubes. It will be very interesting to see how this stove performs. Here is yet another example of the brilliance of our Foundry Fathers. I am continually amazed at them.
I sure think it will be a hell of a lot better than my #77. I think that heat riser in the back is going to throw a lot more heat. The updraft starts below the stove and goes right past the fire pot. And with the built in Baro kinda design it should be easier to run.. Once I learn how... :)

 
User avatar
nortcan
Member
Posts: 3146
Joined: Sat. Feb. 20, 2010 3:32 pm
Location: Qc Canada

Post by nortcan » Mon. Aug. 08, 2011 8:49 pm

The stove will certainly looks super nice. Hope to see it soon...Great restoration.

 
rasct
Member
Posts: 41
Joined: Fri. Jan. 28, 2011 4:05 pm
Location: Central Connecticut

Post by rasct » Mon. Aug. 29, 2011 9:57 pm

Grumpy,

Great job and unique stove, can't wait to see it finished I would love to acid dip my stove parts. How do you dispose of the acid bath after you are done?

Rob

 
User avatar
nortcan
Member
Posts: 3146
Joined: Sat. Feb. 20, 2010 3:32 pm
Location: Qc Canada

Post by nortcan » Mon. Aug. 29, 2011 10:21 pm

rasct wrote:Grumpy,

Great job and unique stove, can't wait to see it finished I would love to acid dip my stove parts. How do you dispose of the acid bath after you are done?

Rob
I used the acid solution to get my cast iron pipe for making the magazine cleaned and it worked very well. When finished, you can keep the acid in a safe covered container for an other cleaning job or dilute it with water and neutralize it by adding baking soda so it will ge a neutral PH. Then you can dispose of it safely.
Just remind to be safe with acid products

 
User avatar
wsherrick
Member
Posts: 3744
Joined: Wed. Jun. 18, 2008 6:04 am
Location: High In The Poconos
Hand Fed Coal Stove: Glenwood Base Heater, Crawford Base Heater
Baseburners & Antiques: Crawford Base Heater, Glenwood, Stanley Argand
Coal Size/Type: Chestnut, Stove Size

Post by wsherrick » Sat. Sep. 03, 2011 10:18 pm

I hope we are going to see the stove back together soon.


Post Reply

Return to “Hand Fired Coal Stoves & Furnaces Using Anthracite”