Harmon Mark III

Post Reply
 
Melandtad
New Member
Posts: 2
Joined: Sun. Jan. 03, 2010 1:39 pm

Post by Melandtad » Sun. Jan. 03, 2010 1:45 pm

WE have had this stove for three years (this being the third) and we have been having alot of wind and this year the wind travels down the pipe and blows through the door...any advice appreciated. I looked the stove up on Harmons website and we aren't sure we should replace the roping or the door kit assembly?

 
User avatar
Duengeon master
Member
Posts: 1958
Joined: Sun. May. 06, 2007 7:32 am
Location: Penndel, Pa.
Hand Fed Coal Stove: Harmon Mark III
Coal Size/Type: Anthracite pea and nut mix. Bituminous lump

Post by Duengeon master » Sun. Jan. 03, 2010 1:52 pm

I have a Harman mark III. You need to put a cap on your chimney to prevent downdrafts in your stove.

 
Melandtad
New Member
Posts: 2
Joined: Sun. Jan. 03, 2010 1:39 pm

Post by Melandtad » Sun. Jan. 03, 2010 2:02 pm

We have a cap on it :) You don't think it has to do with the stove door?

 
rberq
Member
Posts: 6446
Joined: Mon. Apr. 16, 2007 9:34 pm
Location: Central Maine
Hand Fed Coal Stove: DS Machine 1300 with hopper
Coal Size/Type: Blaschak Anthracite Nut
Other Heating: Oil hot water radiators (fuel oil); propane

Post by rberq » Sun. Jan. 03, 2010 2:03 pm

Melandtad wrote:... the wind travels down the pipe and blows through the door ...
Are you using the stove, or is it sitting idle? If it is not in use, then it is quite possible to have a downdraft through the chimney and pipes. Changing the door gasket probably won't help, because there are narrow gaps at the bottom and top edges of the glass that the air can come through. How about disconnecting the pipes from the chimney, and cap the hole into the chimney?

If you are burning coal in the stove, and still getting a draft out through the door, there is something very wrong and it also sounds dangerous, because you could get carbon monoxide fumes back into your living quarters. If you don't have one or two CO detectors in the same area as the stove, get some immediately.

Please describe your setup in more detail -- type of chimney, height, whether it runs inside the house or outside for most of its height, and so on. Pictures are good if you can post some. There are lots of internet links that will show you minimum chimney clearances above the roof and so on.


 
User avatar
Mike Wilson
Member
Posts: 155
Joined: Fri. Dec. 30, 2005 10:54 am
Location: Orient Point, NY

Post by Mike Wilson » Sun. Jan. 03, 2010 2:27 pm

You are getting negative draft, and that is coming from the flue. The door gasket is, at best, simply a symptom. Try one of these:
http://store.chimneycapdesign.com/windcap.html

 
User avatar
SMITTY
Member
Posts: 12526
Joined: Sun. Dec. 11, 2005 12:43 pm
Location: West-Central Mass
Stoker Coal Boiler: EFM 520 Highboy
Coal Size/Type: Rice / Blaschak anthracite
Other Heating: Oil fired Burnham boiler

Post by SMITTY » Sun. Jan. 03, 2010 3:47 pm

Yeah, like rberq said, there is not supposed to be any gaskets on the top & bottom of the glass ... just the sides, & around the door itself. That is to keep the glass clean & provide over-the-fire air for a better burn.

 
User avatar
Cap
Member
Posts: 1603
Joined: Fri. Dec. 02, 2005 10:36 pm
Location: Lehigh Twp, PA
Hand Fed Coal Stove: Harman SF 250, domestic hot water loop, heat accumulator
Coal Size/Type: Nut and Stove
Other Heating: Heat Pumps

Post by Cap » Sun. Jan. 03, 2010 4:00 pm

Chimney peak needs to be 2' above ridge of roof or minimum of 10' from the ridge. Tall trees can effect the wind causing downdrafts. Check it out. Be careful.

Post Reply

Return to “Hand Fired Coal Stoves & Furnaces Using Anthracite”