Burning Too Much Coal?

 
User avatar
Rob R.
Site Moderator
Posts: 17977
Joined: Fri. Dec. 28, 2007 4:26 pm
Location: Chazy, NY
Stoker Coal Boiler: EFM 520
Hand Fed Coal Stove: Chubby Jr

Post by Rob R. » Wed. Feb. 26, 2020 6:49 am

Becker wrote:
Tue. Feb. 25, 2020 9:09 pm
To Rob R.

The boiler is in the house. I do clean those back plates at least once a year. The teeth are set at 4; the air is at 4, as you suggest. I have the aqua-stat set at 165/high and 150/low. I will bump it up if you think that might be the ticket to more efficient burning. The ash ring and fire appear to be correct.
I would set the aquastat as EFM recommends. How do you have the controls setup? Does the boiler run up to the high limit whenever one of your thermostats calls for heat? Do you have a timer installed?

A baro installed on the flue pipe will regulate the draft. If you have strong draft or live in a windy area, the excess draft will burn coal whether you need it or not.

 
Dave 1234
Member
Posts: 788
Joined: Tue. Nov. 13, 2012 9:05 am
Stoker Coal Boiler: 1948 International boiler, EFM S-20 stoker
Coal Size/Type: Buck,

Post by Dave 1234 » Wed. Feb. 26, 2020 8:13 am

So much coal gets used by ,

Timer firing up stoker at hi-limit.
Poor fuel-to-air ratio.
Excessive hi boiler temps, (for several reasons)
''Baro'' not set correctly
Not enough radiation in the living quarters

Dave

{all mistakes that I have made} :?

 
Qtown1835
Member
Posts: 705
Joined: Sat. Nov. 08, 2014 11:47 am
Location: Quakertown, PA
Stoker Coal Boiler: Keystoker '81 KA4 (online 1/16/17)
Coal Size/Type: WAS Lehigh Rice (TBD)
Other Heating: EFM SPK600

Post by Qtown1835 » Wed. Feb. 26, 2020 8:24 am

Becker wrote:
Tue. Feb. 25, 2020 8:29 pm
estic hot water, and I kept the aquastat higher. It was inconsistent, so I have a propane water heater. It is plumbed so that I can feed hot water from the boiler to the hot water tank or directly to the house.
The 520 should provide ample domestic hot for days. The key is having the aquastat set properly for recovery. Also, when is the last time you cleaned the coil? Dirty or clogged coil will surely lead to inferior results.

 
User avatar
CoalisCoolxWarm
Member
Posts: 2323
Joined: Wed. Jan. 19, 2011 11:41 am
Location: Western PA
Stoker Coal Boiler: Keystoker KA-6
Hand Fed Coal Furnace: old Sears rebuilt, bituminous- offline as of winter 2014
Coal Size/Type: Anthracite Buckwheat
Other Heating: Oil Boiler

Post by CoalisCoolxWarm » Wed. Feb. 26, 2020 12:17 pm

Most boilers have a fixed burn rate (with adjustments). The Delta-T (temp difference) in your delivery system (baseboard, radiator, heat exchanger, hot water heater, etc) speaks to the efficiency and output level of heat where desired.

Most baseboard doesn't start to work decent until at least 140F and are often rated at 160F-190F.

Too low of a boiler temp may require too long recovery times, inefficient delivery, and extended run times.

I'll bet if you change to 165F low and 185F high, you'll notice a very pleasant performance difference. The exception would be if you have an extraordinary amount of standby time without any calls for heat.


 
Becker
New Member
Posts: 11
Joined: Thu. Nov. 01, 2018 4:39 pm

Post by Becker » Fri. Feb. 28, 2020 8:05 pm

To LouNY:
I live in Greenwich, too. I'd do a bulk load/haul next year with you if think we can save some money.

 
User avatar
coaledsweat
Site Moderator
Posts: 13763
Joined: Fri. Oct. 27, 2006 2:05 pm
Location: Guilford, Connecticut
Stoker Coal Boiler: Axeman Anderson 260M
Coal Size/Type: Pea

Post by coaledsweat » Fri. Feb. 28, 2020 8:26 pm

How tall is the chimney?

 
LouNY
Member
Posts: 301
Joined: Mon. Jan. 19, 2015 10:12 am
Location: Greenwich, NY
Hand Fed Coal Stove: Hitzer fireplace insert
Coal Size/Type: nut
Other Heating: oil

Post by LouNY » Fri. Feb. 28, 2020 9:32 pm

Becker wrote:
Fri. Feb. 28, 2020 8:05 pm
To LouNY:
I live in Greenwich, too. I'd do a bulk load/haul next year with you if think we can save some money.
I sent you a PM,
Lou

Post Reply

Return to “Anthracite Coal History in Northeastern Pennsylvania”